Models > KHMS155LSS0 > Instructions

KHMS155LSS0 KitchenAid Microwave - Instructions

All installation instructions for KHMS155LSS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KHMS155LSS0
136-150 of 159
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Grease clogged filters

  • Customer: Alan from San Marcos CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slid them out and slid them in. Best part - ordered them at Noon on the Friday after the 4th of July and they arrived at 12:10 the next day - standard shipping.

plastic clips & pieces of original vent broke off and vent grille would no longer lock in place.

  • Customer: Michael from Naples FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered new vent part. Just set in place and fastened screws. These parts do not last because the plastic does deteriorate.

tabs broken off vent

  • Customer: Betty from Faribault MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply removed and replaced 2 screws. Have ordered from this site before and have been pleased with service.

Microwave turntable stopped rotating.

  • Customer: Larrt from Minooka IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

Glass cooking tray for microwave cracked.

  • Customer: Sharon from Kannapolis NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.

broken vent and door face cracked

  • Customer: Anthony from Monrovia IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 2 screws on vent. Door removed 3 screws on inside of door frame that's it repaired

Door handle separated from front panel

  • Customer: Floyd from Coral Springs FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The front panel is held in place by 3 screws on the right edge of the door. Remove the screws then carefully pry off the front panel from the door. This takes some doing so as not to put too much stress on the door itself as you pry the panel off. The back of the panel is snapped into the door so it isn't easy to pry off. Once you have loosened the panel be careful that the glass window and its frame behind the panel does not fall out and crash to the floor. Once the panel is removed and the glass window and frame are safe, you will see 2 self tapping screws on the back of the front panel that holds the door handle to the front panel. I ordered 2 new screws but they were machine screws, not self tapping. Make sure you keep the old screws! Screwing in the self tapping screws to the new handle was not easy. Be sure you have the proper size screw driver so as not to strip the heads. It takes a lot of pressure to get the screws all the way into the handle. Make sure the glass panel and frame are set in properly than push the frame on to the door so it snaps in all the way around. I worked from left to right as I tapped the panel in place. Once it's in place and the screw holes on the panel and door frame line up replace the 3 screws and you're done.

Removing old door panel and installing new one

  • Customer: William from Boulder CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the old door panel by first removing the three screws on the right-hand-side (rhs) of the door.Then pry the old door panel off by using a flat-blade screwdriver. Begin at the rhs near the door handle. The door panel is attached by being pressed into plastic fingers. Once the door panel is loosened from the plastic clips, you should find that it hinges out from the hinge side of the door. If you are just replacing the door panel you will need to remove the plastic retainer and glass plate in the old door panel. These also are retained by plastic clips. You then need to remove the door handle from the old panel since you will attach this to the new door panel. I suggest putting a reasonably large washer on each of the two screws that hold the handle since it is the stress caused by these two screws that caused your old door panel to crack. The washers distribute the stress on the door over a larger larger area. Snap the glass plate from the old panel into the clips on the new door panel. Secure the glass plate with the plastic retainer than you removed from the old door panel. Begin installing the new door panel complete with the glass plate and plastic retainer by first placing it over the hinge side end of the door. The plastic tabs in the door panel should fit into recesses on the lhs of the microwave. Then gently begin pressing the new door panel into the plastic clips on the microwave frame. Work from the hinge side to the door handle side. Congratulations - you have just saved yourself $300+ on the purchase of a new microwave oven!

Broken plastic around screw holes.

  • Customer: Robert from De Pere WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Make sure that the screws go in the holes, after you put the grill in place.

Cracked plastic

  • Customer: Maurice from Indio CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced with new parts

Broken handle (top of the handle actually broke off the screw)

  • Customer: Jennifer from Seymour TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back into place and then replaced the screws.

The capacitor was melted in the microwave

  • Customer: Jocelyne from Fort Pierce FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband open the microwave and see the capacitor melted. He try to find the piece in store,but unfortunatly he didn't find any. I found the piece on the web and ordered it. My husband replaced the part easily. The microwave work very well.The microwave was to our friend. He did replace it by a new one. Now we have a new microwave with a fan.

Tabs broke off the old grille

  • Customer: Lynne from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screws from microwave case. installed new grille. inserted screws into holes in case. Tightened screws to secure grille

Broke glass tray

  • Customer: Katherine from Cleveland TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Arrived in 24hours!!! Great.

grille fell off and brackets broken

  • Customer: donna from Acton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Really easy to attach new grill at the bottom first (saw that on another persons installation instructions) then used a Philips screwdriver to attach top of grille in the two places one at each end., not a problem 75 year old gal, If I can do it you can do it...
All Instructions for the KHMS155LSS0
136-150 of 159