Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KGYS750GQ1 > Instructions

KGYS750GQ1 KitchenAid Dryer - Instructions

All installation instructions for KGYS750GQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KGYS750GQ1
1,336-1,350 of 1,466
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would not start

  • Customer: Robert W Garven from Ventura, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My black very cool 15 year old Kithenaid electric dryer stopped working. No power. I tried the timer and it was still clicking like it was working. I opened the door then pushed the on button and heard a click which made me feel the door switch and on button were working. I replaced the cycling thermostat and thermal fuse and everything is fine. I wish i would have bought the other thermostat as I was right there and it was not that much. Dyer is working fine. This site is great. My repair guy moved out of state...I also disassembled the vent tube and vacuumed out all sorts of stuff and vacuumed the motor and all the area I could get to with the back, top and lower cover removed and waxed the dryer.

Replace Drive Belt

  • Customer: William from Marlborough, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
What a pain in the butt to route the belt thru the tensioner! There's room for only one hand in there. The guys who do this for a living must have some secret. My solution was to drill a 3/16 hole thru the side, make a j-hook from 8-32 threaded rod, use that and a wing nut to pre-load the tensioner, route the belt, then slowly back off the wing nut until the belt was tight. It works. . . .

not enough heat

  • Customer: Charles from Bay City, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first I unplugged the dryer. Then I removed the back of the dryer with a 1/4" nut driver. with the back off using the same 1/4" nut driver I removed the one screw that holds the cycling t-stat slowly remove the t-stat and take one wire off at a time and plug it onto the new t-stat once all wires are replaced. place the t-stat back in and secure with the screw. Then put the back of the dryer back on. put the dryer vent hose back on. plug in and away you go. repair done. If that doesn't fix it. Then the next step is probably to check the gas valve coils. That is a little more difficult repair but not to hard.

Dryer quit heating.

  • Customer: John from La Crescenta, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws from front panel and lifted front panel away, Turned it to the left so I could keep the door switch connected. The dryer would heat when it was first started, but then the burner would go off and would not come back on. I ran the dryer with the front panel off and could see the igniter glow and light the burner, but after the burner cycled off, the igniter would come back on but the gas would not come back on. I could tell it wasn't the thermostat because the igniter would come on, so I knew it must be the gas valve, and therefore probably the coils. The instructions on the website said that the coils were frequently intermittent, so that seemed like the problem. I tried checking out the coil resistance with an ohmmeter to try to confirm that, but couldn't really tell anything that way. I ordered the replacement coils Tuesday night, selecting the cheapest shipping; they shipped on Wednesday, and were delivered on Thursday! Amazingly fast! Removed two screws from the clip that holds the coils in place, unplugged the old coils, swapped in the new coils, screwed the retaining clip back on. All done. Before I replaced the front panel, I watched to see that it operated correctly. I could see the burner cycle off, then after a bit, the igniter glowed, and then the gas came back on and lit, just like it should. Problem solved. Put the front panel back on, and that's all there was to it. Well, I did vacuum out some of the dust inside the cabinet while I had the cover off. Just out of curiosity, I checked the resistance of the new coils before I installed them to compare with the old ones. Couldn't see much difference.

Dryer would start and run but no heat was produced.

  • Customer: andres from yucaipa, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched several videos online and was suggested that the thermal fuse was bad, so i replaced it but no fix. So i checked the previews Q&A from other costumers and watched the videos on how to replace different parts. I first looked thru the peep hole on the bottom left part of the dryer and saw the igniter glow for about 10 sec every minute but no flame would start. So i replaced the igniter, the flame sensor, and the coils all at once. I know thats not the proper way to troubleshoot something but i was gonna take the drum out and everything so mind as well replace them all. Dryer works like new and dont have to listen to the wife complaint anymore!!!

Broken Belt

  • Customer: gary w from Saint Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pop off the top , Then one screw holds each side . slide belt around drum and then preload tensioner as per instructions . Simple!

no heat

  • Customer: Tanimu from Mansfield, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I replaced both the Thermal fuse and Cycling Thermostat, both of which cost less than fourty dollars. just removed the back panel, and replaced the parts in less tham a minute. Replaced the back panel. Job done.

heat cycle runs once then does not come back on

  • Customer: john from garden city, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
follow Steve the repairman's instructions they were very good

Dryer would not maintain heat

  • Customer: Joe from Freehold, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I started with the process of elimination, based on the web site part failure percentage...so I started with the cycling thermostat and thermal fuse, without success. Next, I placed an order for the 'M' Series New Style Coil Kit Part # PS334310. Which, are located behind the lower front panel

Dryer turned on and drum rolled. but no heat or igniter glow.

  • Customer: Victor from Bellport, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My wife hates me because I keep repairing our appliances. The dryer and washing machine are now 21 years old and look like new. To replace these two parts, first check if the igniter is glowing at all when you turn the dryer on. To do this remove the access panel in front on the bottom. To remove it, slide a flat screw driver across the slot onto of the panel to locate the release clips. Depress the release clamps by sliding the screw driver on top and pull the panel forward. Now start the machine and see if the igniter glows. If not proceed to replace the Thermal Fuse and both thermostats. To do so, open the back panel of the unit. First disconnect power and vent. Unscrew and replace components which will be easily seen on the bulk head. Use a pliers to remove the contacts. Your machine will now last another twenty years and your wife will hate you as does mine:)

Did not heat

  • Customer: Richard from Hesperia, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took the back cover off. Replaced fuse and put the cover back on. Worked great.

Small black tab had broken off from door switch assembly

  • Customer: Stephanie from Mountain View, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After reviewing a variety of online instructional videos I was able to figure out how to remove the top ("hood") panel of dryer to access the door switch. Once I had access the switch was relatively simple to replace.

Dryer would not shut off, constant heat.

  • Customer: Michael from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replacing the cycling thermostat went really fast and easy. Unplug the dryer. Remove the 6-8 hex-head screws holding the back panel in place. The thermostat location is in the lower left. below the black discharge air duct. Note the location and/or tag the wires connected to it. Pull off the wires and remove the screw holding the thermostat in place and remove it. Reverse the procedure for installation of the new thermostat. Where this got tricky was it did not solve the problem. A strict diagnosis based on the electrical schematic alone would have, and did, indicate a faulty thermostat, i.e. on that was not opening. However, what I found was surprising. The heating element coil had broken and part of it had "welded" to the casing, grounding it and effectively turning the 240V heater into a 120V heater. This allowed the heater to provide heat (low heat). However, the timer motor needs 240V to operate and since one leg of the heater was grounded the timer could not get 240V when the thermostat cycled off. Replacing the heating element solved the problem.

My dryer just suddenly wouldn't come on.

  • Customer: Walter from LaVergne, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the Thermal Fuse, as it appeared to be the problem. A friend suggested that as long as the price was fairly reasonable, I should go ahead and get two of them and keep one for later. I ordered/paid for two of them. I put the Thermal Fuse in, and when I attempted to turn the dryer on, it ran for about 5 minutes, at a very hot heat, dried the towels, and then would not come on again. I thought it had kicked the circuit breaker, but after checking, found it hadn't. I watched the youtubes.com again and found that there were three other parts that it could possibly be. I ordered them, and replaced all of them. One of them had 4 prongs but two on the new one. I left two wires off, and sure enough, it would not run. I borrowed an ohm meter, and found out my old part was still good, but that in the process it had blown the Thermal Fuse, of which I just happened to have an extra, and after installing it, it is now in perfect running order. The total repair was about $80-100, rather than a $75.00 bill for service and heaven only knows for the parts at the repairman's price! Thanks youtube, Parts Select and my friend for his advice! Walter

no heat. ignitor glowed but burner would not light

  • Customer: mike from harbor beach, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
eliminated themostats and ignitor as problem. the next logical problem was gas valve coils. turned out to be the problem and machine is back in service. gave machine a good cleaning and vacume job while it was apart and learned that drying rugs in it had caused a build up of rubber backing material in a couple of areas. could have been a fire hazzard. periodic cleaning inside is a must for fire safety
All Instructions for the KGYS750GQ1
1,336-1,350 of 1,466