Models > KGYE777BWH1

KGYE777BWH1 KitchenAid Dryer - Overview

Get Parts and Repair Help for KGYE777BWH1

If you know the dryer repair part you need, you can browse the list of all parts on the KGYE777BWH1, or you can search by name or part description. You can also find your part by where it is located on the KGYE777BWH1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for KGYE777BWH1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$12.77

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

$13.70

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$13.95

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$16.38

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.

$4.06

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$2.52

Light Bulb - 40W

Sold individually.

$22.75

Igniter Kit

This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is ...

$25.66

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$11.96

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

$3.46

Leveling Foot

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1044 of 1198 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 500 of 509 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more

Dryer tub belt broke

  • Customer: Ray from Denton TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 495 of 521 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more