Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KGU5950BS

KGU5950BS Maytag Refrigerator - Overview

Get Parts and Repair Help for KGU5950BS

If you know the refrigerator repair part you need, you can browse the list of all parts on the KGU5950BS, or you can search by name or part description. You can also find your part by where it is located on the KGU5950BS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KGU5950BS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$96.00

Replacement Ice Maker

This is a replacement ice maker. This assembly includes the ice mold and the control device. The water inlet valve pumps water into the mold, which stays there until it is frozen s...

$3.02

Screw

This screw is sold individually.

$11.11

Light Rocker Switch

This light rocker light switch is used in a number of household appliances. It is most often found in refrigerators and freezers. This is a simple mechanism that helps turn the lig...

$5.52

Screw

Sold individually.

$37.73

Condenser Fan Motor Kit

This condenser fan motor kit is designed for use with refrigerators. This fan draws air through the condenser coils and over the compressor. It does this with the goal of cooling t...

$4.89

Screw

Sold individually.

$5.27

Lower Hinge Pin

This lower hinge pin is almost two inches long. It is made entirely of plastic and it is all black in color.

$24.54

BLADE-FAN

The fan blade is used to blow air over the condenser.

$2.96

Screw

Sold individually.

$33.37

Single Outlet Water Valve

The single outlet water valve may also be known as the water inlet valve and is compatible with your refrigerator. This valve has a quarter-inch tubing inlet connection. When energized, this part releases water from the supply line into the ice mold. The purpose of this part is to supply water to the water dispenser and the ice maker within the refrigerator. To make this installation you will need a quarter-inch nut driver and a sharp utility knife. To make this repair you will need to pull your appliance away from the wall and disconnect the electrical source and the water supply.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 729 of 773 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 255 of 330 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 133 of 143 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more