Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KGST307FWH0

KGST307FWH0 KitchenAid Range - Overview

Get Parts and Repair Help for KGST307FWH0

If you know the range repair part you need, you can browse the list of all parts on the KGST307FWH0, or you can search by name or part description. You can also find your part by where it is located on the KGST307FWH0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for KGST307FWH0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$21.46

2 Piece Broiler Pan

The top of this part is now black.

$7.27

Bumper Pad Set of 4

***NOTE: This part has been substituted by the manufacturer and may not appear the same as the original but should function the same. These pads go on the bottom of your gas cook...

$7.22

Touch-Up Paint - White

18ml

$19.29

Single Drawer Roller

Used to slide the broiler drawer open and closed.

$5.70

Appliance Scraper

Use this scraper for your ceramic/glass cooktop. It has a retractable blade and is an all-purpose tool for cooktops, mirrors, windows and tile. Use it to also remove paint, paper, dirt, stickers and more.

$11.07

Spray Paint - 12 oz. - White

$44.70

RACK-OVEN

$20.80

Spray Paint - Surperior Black

This is a 12oz can of black spray paint.

$37.73

Knob - Black - Kit of 4

These knobs accept a D-shaped shaft.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 123 of 159 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Oven stopped working/Slow to ignite

  • Customer: John from Chicago, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 42 of 46 people found this instruction helpful
Although the ignitors glowed brilliant yellow I learned from an expert there are 2 fail modes. 1. that they break and don't glow well enough to ignite the gas or 2. they get resistive over the years and do not pass enough current to open the valve. This is important to know because the current passes through the ignitor before it gets to the valve. If the... read more

Oven wouldn't light

  • Customer: james from downers grove, IL
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 43 of 65 people found this instruction helpful
My analysis was flawed. The $100 gas valve was acting erraticaly, so I replaced it. On a hunch, I took the top front off the stove and immediately saw a row of mini relays mounted on the $300 control board. The one labeled "bake" was black!
It is just too small for years of gas on / gas off high current. (The gas valve is indestructable. I took the ol... read more