Models > KGRT607HBS9 > Instructions

KGRT607HBS9 KitchenAid Range - Instructions

All installation instructions for KGRT607HBS9 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KGRT607HBS9
1-15 of 106
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Inside door glass broke

  • Customer: MANNY from LIVERMORE CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 60 of 68 people found this instruction helpful
I removed the oven door by lifting it off with the hinges. Disassembled the door parts one at time making sure I remember where I removed the screws until I am able to get to the broken glass. The most difficult part is making sure that the insulation strip & the gasket stayed in place after I replaced the broken glass & doing the reverse process of installing the parts together. Relatively easy process as long as you remember where the parts go. When in doubt, I had to refer to the pictorial of the disassembled door shown on your website.

no heat in oven,broiler did work ,that shows gas valve functioning correctly

  • Customer: Richard from Garden City NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 33 of 39 people found this instruction helpful
I removed bottom drawer of the kitchen aid oven.I could see the gas valve.I opened the door of the oven and removed plate on bottom of the oven .there was no screws holding it down ,I removed a couple of screw for the burner and took out 2 screws for the heating element . In the back of the oven .there is 2 wires .one goes to the gas valve located behind the bottom draw.you know can see it from the front with the draw removed,than move the oven out and take the 4 screws holding the back plate .you will see the other wire the element plugs into .you unplug 2 wires and a few screws and you are done.you save alot of money and since this happens alot .you can compare this to changinging a light bulb.It needs maintence from time to time.

Oven wouldn't light

  • Customer: james from downers grove IL
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 35 of 52 people found this instruction helpful
My analysis was flawed. The $100 gas valve was acting erraticaly, so I replaced it. On a hunch, I took the top front off the stove and immediately saw a row of mini relays mounted on the $300 control board. The one labeled "bake" was black!
It is just too small for years of gas on / gas off high current. (The gas valve is indestructable. I took the old one apart. It's only a heater wire wrapped around a bimetalllic arm that lifts a soft pad off of the valve orfice.)
I removed the control board and desoldered the "bake" relay and the "light" relay. I cleaned up the bad "bake" relay contacts and swapped the two relays. Works fine. Better $100 mistake than a $300 control board. (Could have been $0, though.)

Inner Oven Door Shattered during cooking.

  • Customer: Gloria from Melbourne FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 24 of 27 people found this instruction helpful
First, layed tape across all broken glass to keep glass from shattering more and releasing more bits of glass. Pull up and out the oven door. Had table set aside covered with an old sheet to lay door on, After laying door on table, Removed outer screws. Needed phillips #2 & #3 tip widths and electric screwdriver, for inner screws that where difficult to remove. Making notes of what came off first! ( (rt & left, bottom,/top) when removing metal frame braces, and in what order they go in when reassembled . Did the same with screws & set them aside in groups. Then marked the groups of screws. Removed the metal door panel. Carefully removed the in between panel of glass. Set Outer glass aside along with metal "door"and inner door glass,and proped them up in a safe place. Carefully removed the broken & shattered inside glass wearing rubber gloves. Had a garbage can next to the table to with news paper to wrap glass. Cleaned area. Replaced glass taking care not to tighted screws so much as to break the glass. Put added insulation.(Whcih was not the same as in diagram), around the edge. put back the inner glass panel, care not to leave prints, tighten screw ( care not to break glass) Cleaned the door sides and bottom, all had alot of grease buildup.
Put back the metal door portion. Cleaned the outer glass door front and back. Being careful not to break it (or leave prints inside). Replaced the side and bottom metal frames. Wiped it down and put door back on stove.

igniter not coming on

  • Customer: Charles from Carteret NJ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 22 of 31 people found this instruction helpful
slide out range shut off main gas.

remove storage drawer.

disconnect supply hose.

remove oven door (esier access to burner assy

remove burner covers. unscrew igniter assy.

remove rear panel, disconect igniter, pull wires through
front, remove igniter.

reverse process to install new igniter.

Socket Light had a bad thread

  • Customer: Edmund from Emporium PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 21 people found this instruction helpful
Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover

Inner door glass on the range was broken

  • Customer: Jaime from Melbourne FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 14 of 17 people found this instruction helpful
I let my husband fix this one, so he can tell you about it!

Step one--remove the oven door and place on a padded surface to protect both the door and the surface (table top).

Step 2--remove the screws holding the outer door panel in place.

Step 3--remove the screws holding the middle door panel.

Step 4--remove the middle panel of glass then the screws holding the spacer and inner panel of glass.

Step 5--carefully remove the (remains of the) inner panel of glass.

Step 6--replace the inner panel of glass and make sure both sides are clean.

Step 7--reinstall the items removed (in reverse order).

Step 8--replace the oven door onto the range.

Hinges were broken

  • Customer: Sheila from Tustin CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 15 of 21 people found this instruction helpful
Take the door off the oven by sliding out the old hinges that hold the door on to the oven. Put the door up on a protected table so that the hinges can hang down and free of the table. This step will make the job go much more simple. Proceed by removing all visable screws. Make a mental note on how the old hinges are held in and how the door comes apart. Take your time this is not a hard task! I am a homemaker, was taking care of my grandson that day and still accomplished the task in under an hour. The repair people wanted $145.00 labor only to install this part!

broken inside glass on door

  • Customer: michael from Honeoye NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
repair was easy except one part drove me nuts... when putting every thing bacck together i found out that the front glass panel sits on top of the side covers of the door ...looking at the side covers you would think they fit over the top of the front glass...not so the glass edges show and are not covered ... hope this helps someone else

Top burners would not light. No "clicking" .

  • Customer: Carolyn from Bellingham MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
My husband and I replaced the igniter module, following directions we found online. We removed the old one, replaced it with the new one, and thankfully everything is working great!

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

inside glass broke due to oversize pan

  • Customer: Robert from Las Vegas NV
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 11 of 13 people found this instruction helpful
After reading all who did a simular repair, I was better prepaired for what to expect before my wife and I bagan to take apart the oven door. It may help or hinder if you had extra help. At least two people and no wittnesses for intertainment.
Consider paying to have it done if your not willing to attempt to repair the oven door glass from this poorly designed door and its componets.

I wish we had a video camera to record the repair due to all the steps involved.
For the most part, all internal parts float together and only the most inside sheet of glass is screwed down.
You will need a work table to place the door on, scewdrivers, penatrent spray, cleaning solution and rags or towels.
After removing the door from the stove, just by opening the door slightly and lifting upward evenly, the door will come off the stove with its hinges attached.
With the door front facing up, and handle off the work table so door lays flat, we removed the screws along the bottom of the door.
With the screws removed, the bottom strip comes off. A strip on each side may now drop off.
This will allow you to lift the bottom end of the panel just enough to detach it from the clips that hold it on the top end. Theres one on each side.
The 2 fixed clips go inside slots of the door panel.
It may take a little tugging back and forth, up and down to remove the panel.
There are side strips by now will come off now too.
Once this panel is out of the way, you can remove each piece. Remember the order and record if you can.
The glass that was broke is secured by screws that may require some spray penatrant to loosen.

Make sure you use a perfectly fitting screwdriver as to not strip out the screw heads.

Carefully remove all broken pieces of glass than vacuum the surrounding area.
Clean all glass panels with glass cleaner and paper towels or newspaper.

With the heat gasket in its proper place, install trim with a new glass panel and return each piece in the order you removed them.

Make sure everything is returned to its proper position before you re attach the inside door panel. It may require a little effort to align everything together to accomplish this.

Return the door to the oven by inserting the door hindges into the door slots and you are done!

Sit down, have a cocktail and ask yourself if it was worth the trouble. I thought it was.

Igniter problem on one gas burner

  • Customer: Roland from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement, very quick fix.

I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.

replaced inner glass that cracked when some cool water was drizzled on it accidentally

  • Customer: C Bradley from Grand Junction CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
The easy part is removing the oven door and reinserting the oven door. Disassembly of the door was straight forward enough by removing the screws from the attached bottom plates. Separating the inner door from the out door was quite the pain. Once accomplished I was surprised to learn that the outer glass pane was not attached but free floating inside the door frame. Also the outside aluminum frame that the outer glass pane laid over was also unattached and free sliding in betwwen the inner and oute door. Getting this back into place then laying the free floating glass pane and keeping it positioned prior to re assembly of the inner and outter door was a tad nightmarish. The actual removal of the brackets to remove the inner broken glass plane was very easy. This is where a good drill or power screw driver comes in handy. Once the brackets holding the glass were removed, you take the broken glass out, put the new in, then reattach that glass pane with the brackets.Hat's off to those who did this whole project in 1/2 hr or less. It was a solid 2.5 hrs of time for me and my wife and I can't say that we drew closer together on this project. Actually a wall of separation started to develop between us until with God's help we finally got the whole door back together and in the oven. Be strong in the Lord and in the power of His might when you start to take on this project. Amen

Inside brass liner in socket came out when bulb was removed. Apparently had welded itself to the base of the bulb

  • Customer: Lewis from Chapin SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 9 people found this instruction helpful
Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.
All Instructions for the KGRT607HBS9
1-15 of 106