Models > KGRA806PSS02 > Instructions

KGRA806PSS02 KitchenAid Range - Instructions

All installation instructions for KGRA806PSS02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KGRA806PSS02
1-15 of 49
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

When using self cleaning, oven door wouldn't open and screen panel went blank.

  • Customer: Abdurehman from Lawrenceville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 44 of 47 people found this instruction helpful
I searched similar problems on the web and learned that a whole lot of people have Kitchenaid stove with the same problem. They all stated that the thermostat burns when self cleaning. Since technician wanted $190.00, I decided to change it myself. The part cost me $40.00. To instal the thermostat, I removed the panel at the back of the stove and the thermostat is attached with two wires. After I replaced the thrmostat, the screen panel came on and I was able to open the door. I am posting this to tell people that anyone can do this.

During the cleaning cycle, oven died and door locked

  • Customer: Randy from Bellevue WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 19 of 20 people found this instruction helpful
Apparently this is a common problem (defect) with KitchenAid ovens of various models. I am not a repairman, but replacing the thermostat was very simple. I pulled the stove out and removed the large back panel of the oven. The was right there in the open, impossible to miss. It looked identical the the replacement thermostat. There are only 2 screws and 2 wires to push on and it's fixed. Anybody can replace this part easy. I hope the replacement part is better than the original!

faulty meat probe

  • Customer: Kent from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 23 people found this instruction helpful
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

Kitchenaid Stove Dies After Cleaning

  • Customer: Andy from Beaverton OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
I have a Kitchenaid stove that completely shuts off in the middle of the self clean cycle. I did some research on the internet and discovered that it was the thermostat (aka thermal fuse). It was a real easy repair. All you have to do is take off the back panel. You will see the thermostat in the upper left of the machine (there are two wires connected to the part). The part is fairly expensive around $45. No one in town had the part so I had to order from Partselect.com (which was very easy to find). The repair was simple, all you need to do is connect the new thermostat in place of the old one. Dont forget to unplug the stove before you get started. After replacing the part the stove worked just fine. From what I can tell from the research this is a common problem and there is no permanent fix. We are resigned to not using the self clean mode on the stove which is a drag, but it is cheaper than buying a new stove.

Self-clean feature caused control panel to die and oven to stop working. Oven door remained locked.

  • Customer: Karen from Clintondale NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
This is a known defect with KitchenAid ovens. If your range is out of warranty, KitchenAid will do nothing to help. (They should really issue a recall). I figured out through research that the part is the thermostat fuse, so instead of paying a repair company to come to the house, diagnose the problem and do the repair, I ordered the part on PartSelect.com. I probably saved myself $200. My husband did the repair and said it was really easy. It took him 10 - 15 minutes. He took a picture of the back of the oven with the back panel off, showing where the part is located, but looks like I'm not able upload images. All you need is to be able to pull your range out to get to the back of it and a screwdriver to remove some screws and replace the thermostat. Once the part was replaced, the control panel came back on, the oven unlocked and is now working again!! I will not use Self-Clean again - that is for sure!

al 4 interior lights had burned out

  • Customer: Kimberlee from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 13 people found this instruction helpful
The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

oven and broiler not working

  • Customer: Pamela from chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 12 of 20 people found this instruction helpful
I just looked at the tech sheet on the range and tested the gas valve with an ohm meter to see how much resistance I had and compared it to the tech sheet and noticed the gas valve was bad. So I replaced it with a new one from part select which arrived very fast. It was quite easy to replaced it.

Original oven gasket had discolored and deteriated, mainly due to use of oven cleaner.

  • Customer: Ralph from Green Bay WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
I removed the bottom gasket retainer , single screw, with a screwdriver. The old gasket just pulls away. I cleaned the area under the old gasket with soap and water. I installed the new gasket whcih easily slips in place with the already installed retainer wires into the pre drilled holes.

Viola. Lokks like new.

Gas range oven door stuck shut during self-clean

  • Customer: James from Cloverdale CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
The thermostat blew during the oven self-cleaning cycle (apparently it's a common problem). Take off a few panels in the back of the range with a screw driver. Pull the terminals off the existing thermostat and (safely) touch them to make sure it's not some other problem. If the oven comes back to life order this part. Unscrew the blown thermostat and attach the new, plug the terminals and re-attach the back panels.

Oven not preheating

  • Customer: James from Bel Air MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 8 of 11 people found this instruction helpful
I called the place that I ordered the range from and set up a repair date. The repairman came out and diagnosed the problem and had to order the part (Valve). I noticed on the repair ticket the cost of $172.00. I checked out this site and found it a whole lot cheaper. I called the repairman and advised that I found the part cheaper and expected them to tell me they would adjust the price of the repair. They told me to order the part and let them know when it came in. I got it two days after I ordered it. I called the repairman who came out and installed it.

stove will not start no spark or gas

  • Customer: HERBERT from ISELIN NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 17 of 38 people found this instruction helpful
part did not fix the problem, may be gas regulater ,well if you are changing this part,not to bad .remove the knobs bottom screws and two side screws front cover flips up and off ,the ignition control is in front of you right side ,remove the one screw that is looking at and everything slides out .i turned off the gas and elec and removed the gas line and carefully laid the stove on it back.made it easier ,good luck

oven drawer would not slide...because of worn out nylon roller.............

  • Customer: HAROLD from HELENA OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

during self clean oven shut down and door would not unlock.

  • Customer: steve from scituate MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
after reading tips on your site I just removed 1/2 dozen or so screws
took off back cover, part was right in the open, 2 more screws unplugged/replugged part, it worked! couldn't have been easier.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

function key stuck

  • Customer: Jeffrey from Vicksburg MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
The repair was easy, I used one screw driver and that was it, less than an hour. Part worked great! Before I repaired the oven, I was told by a service tech. the repairs would cost $693, I repaired myself for $166 tnru part select . Using a Philips head driver I unscrewed two screws holding the front panel onto the stove, unplugged the control panel. Unscrewed the mother board pulled old membrane switch out replaced it with new. Its that easy. Then reverse the process.
All Instructions for the KGRA806PSS02
1-15 of 49