Models > KGCT366GBL1 > Instructions

KGCT366GBL1 KitchenAid Cooktop - Instructions

All installation instructions for KGCT366GBL1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KGCT366GBL1
1-15 of 17
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the knob was melted by a hot pan

  • Customer: David from Corinth TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
popped off the old knobs and put on the new ones in less than a minute

Stove is over 50 years old, all knobs were broken or worn

  • Customer: CAROL from ORANGE CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 13 people found this instruction helpful
Went to a local appliance parts store and could find only black knobs--there were two kinds--one $3 each, the other $8 each. Both kinds looked AWFUL so I went on line and found partselect.com which had suitable knobs at a very reasonable price, ordered them and they were shipped the next day. Who could ask for anything more? The service was terrific.

Knob on range top did not work.

  • Customer: James from Hurst TX
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
Since removing the burner valve would disable the cooktop, I ordered the valve first. Unfortunately the valve could not be removed because the screw that hold it in place was frozen to the valve and manifold. I finally had to cut the screw off with a hacksaw. Since the screw is a special screw, substitutions did not work, so I had to order the screw and pay shipping a second time. These screws should be included with the valve. Anyway, the hacksaw did some slight damage to the manifold so that the screw did not seal off properly. I had to use a Dremel tool to smooth the surface and then use fiberglass to coat the surface to seal any scratches or potential leaks. I screwed the screw in after applying the fiberglass resin to the manifold surface while the resin was still pliable. This seemed to seal the manifold off so that there is no leak, but it does make me nervous. Because of having to reorder for the additional part, the range top took almost a week to repair and could not be used during that time all because the screw was not included with the burner valve. Also a screw with a larger head would have allowed a larger wrench to be used and the screw could have been removed easily. The screw head was so small that it rounded off from the wrench making it more difficult to remove.

Gas knobs on the cooktop had been melted by a hot frying pan placed on them by mistake.

  • Customer: Donald from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Ordered new knobs from PartSelect. I ordered the wrong part. The young lady I spoke to not only quickly arranged for a return and refund but offered to order the correct parts which were received and now the stove looks like new.

Had melted knob on cooktop

  • Customer: Traci from Bozeman MT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Went great, part was perfect!

Burner knob appeared to have been accidentally melted by placing a hot pot on top of it.

  • Customer: Jodie from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I took the melted knob off, located the part # went online and found this site. I immediately found the correct burner knob, ordered it, and it came very quickly to my home! I just popped it right on the cooktop, and it's as good as new.

control knob was melted from a hot pan

  • Customer: JUDY from AIKEN SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Easy as 1 2 3. Removed ruined knob and set new knob on post. That's it. Complete success!

Stove top did not come with a gas regulator and nipple attachment

  • Customer: Linda from Colorado Springs CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 9 of 28 people found this instruction helpful
A plummer did the repair.

the little tabs that hold the skirt in the hole break off

  • Customer: John from Sequim WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I pulled the knobs off, lifted the broken skirts out and snapped the new ones in.

backing for stovetop knobs

  • Customer: Norman from Tustin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
the decorative backings on our stovetop knobs had become frayed, and I simply pried off the old ones,and installed the new ones. I have use Parts Select for years for various parts replacement, their service is quick and accurate. When I need a part, I always check here first.

lost gas top knobs

  • Customer: Bonnie from Collegeville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just put them on and pressed down

Worn out spring assembly in valve.

  • Customer: Stephen from Ladera Ranch CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
This was remove and replace of burner valve on a rangetop stove. Removed front pannel of stove. Removed lower panel support. Removed ignition/spark material/peice (slides right off). Unscrewed valve form underneath through access hole, and unscrewed gas connection on top. Removed and eplaced with new valve and reassembled everything in order. Fairly straight forward.

Old skirts tabs broke off with age

  • Customer: Leanne from Huntingtown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just replaced them.

change over from Natural Gas to LP and install cooktop from Electric to gas

  • Customer: Dan from Olalla WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
removed old electric cooktop and install gas line and gas cooktop and change from natural gas to LP remove and replace orifice with new ones from kit, my cooktop called for 2 black orifices in the two small burners but did not come in the parts kit that I orded so I used 2 red orifices and it seems to work just fine.

Burners will not light in the light position

  • Customer: Wesley from Edgewood WA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
With no inctructions removed the counter top burner tried to figure out how to remove the glass. Next removed the burners (remember to place the burnersin a open area in the exact order you remoned them from the stove)The burners are not the same. Now the glass was acessiable to remove. The switch harness was easy to replace. Removed one switch at a time noting how the harness was routed.Remember the stove is upside down. First remove the rubber dirt sheild and washed each sheild. Note the key way on the gas adjust shaft there is a knotch on the switch that must be located and pressed in to place. Complete the 5 switches noting not to remove the termination of the harnes until the very last step. That connects to the main power. I had to cut a wire tie and replace to complete the process. Removing a burner takes a star bit to unscrew the burner from the stove top.
All Instructions for the KGCT366GBL1
1-15 of 17