Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KEYW870BWH0

KEYW870BWH0 KitchenAid Dryer - Overview

Get Parts and Repair Help for KEYW870BWH0

If you know the dryer repair part you need, you can browse the list of all parts on the KEYW870BWH0, or you can search by name or part description. You can also find your part by where it is located on the KEYW870BWH0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for KEYW870BWH0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the KEYW870BWH0

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

Order within the next 4 hrs and your part ships today!
$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees and will then turn off and then on again once it has dropped by 25 degrees. If your dryer is not giving off enough heat, is over-heating, is not turning on, or is having issues with the timer functionality, this could indicate an issue with the thermostat. The installation of the cycling thermostat is simple and the only tool required is a 1/4 inch nut driver (and gloves for safety).

Order within the next 4 hrs and your part ships today!
$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer do...

Order within the next 4 hrs and your part ships today!
$36.63

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one high-limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires. If your dryer is not starting properly, shutting off too soon or is taking too long to dry your clothes it could be because it has blown and needs to be replaced. This is a genuine OEM part that comes directly from the manufacturer.

Order within the next 4 hrs and your part ships today!
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

Order within the next 4 hrs and your part ships today!
$10.34

Drum Support Roller

This is a drum support roller for a dryer. The part includes the drum roller only and does not include the tri rings. Although most dryers require two drum support rollers, this part is sold separately. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy. This is a genuine replacement part.

Order within the next 4 hrs and your part ships today!
$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not s...

Order within the next 4 hrs and your part ships today!
$5.96

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

Order within the next 4 hrs and your part ships today!
$31.06

Lint Filter

This dryer lint screen comes with a handle. This filter collects lint as it passes through the dryer vent.

Order within the next 4 hrs and your part ships today!
$5.00

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer tub belt broke

  • Customer: Ray from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 813 of 865 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more

No Heat

  • Customer: Vernon from Niceville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 798 of 843 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more

Dryer blew cold air.

  • Customer: Tom from High Point, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 661 of 700 people found this instruction helpful
PartSelect is great for providing parts as requested. Unfortunately, neither of the 2 parts I ordered were on my machine. My bad for not looking at the actual part instead of the description. A word to the wise! read more