Models > KEYS850LQ0 > Instructions

KEYS850LQ0 KitchenAid Dryer - Instructions

All installation instructions for KEYS850LQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEYS850LQ0
1,021-1,035 of 1,179
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Old belt broke

  • Customer: Arthur from Sun City Center, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Pulled the front of the dryer off. Removed the old belt. Replaced the new one by threading it flat side down, except for the drive motor which was ribbed, so the belt had to be installed sort of serpentine like. Replaced front of dryer and it's like new.

Broken belt

  • Customer: Clayton from Girard, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed video instructions. Raised the top, slipped off the front, installed the belt, aligned, installed tension part, reinstalled front, lowered the top and inserted lint trap. Job done. Quick and easy. The video was the key to the whole project.

Broken drum belt.

  • Customer: Bradley from Palm Bay, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This was my first dryer repair. The only difficulty I had was figuring out how the belt tensioner was set up with the belt. The old belt broke so I didn't know how it was suppose to work. Anyway, it took a few minute to figure out that one end of the bracket was a "spring" that allowed it to flex a long ways! Pretty easy job.

Broken belt

  • Customer: James from Chicopee, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the installation video. It was exactly as shown.

Installed a new belt

  • Customer: Timothy W from Lakeland, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The video you had of my dryer was different then my dryer and the pulley was in the middle of the bottom and the motor and fan were in front of it. I had to replace the belt without being able to see what I was doing. I couldn't get it at first then realized there was tension on the pulley wheel and had to pull it towards the other wheel in order to get the belt on there. Once I pulled the wheel it went on really easy. My first time working on a dryer but I knew I could do it myself.

broken dryer belt

  • Customer: Thomas from Waterford, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
instructions were clear and repair was easy

Does not turn or tumble

  • Customer: Charles Weston from Pikesville, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Well, to Figure the issue I took the entire thing apart. Actually a lot more than needed. I found the torn belt and ordered it. I did not realize I may need a new belt tensioner which is sold with a wheel for the belt to wrap around and be tensioned by. Actually the original just utilized a rubber c or u shaped design(no wheel) for the belt to slide over. Anyways, instead of ordering and waiting for a new wheeled belt tensioner, I installed new belt with all original parts and working fine. I did oil up the drum rollers to reduce noise. And since I took the whole thing apart I cleaned the lint from every place it could hide. Ps a coke can is said to be helpful to hold the drum up while installing the belt but I found a jug of laundry detergent did better. Totally easy project for someone with no appliance repair history

broken belt that makes the dryer drum go around

  • Customer: kevin from madison, WI
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Broken belt

  • Customer: Tracy from Bakersfield, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I unplugged the dryer then loosened the screws on the top and inside front, took the front off, I didn't need to unplugged the socket wiring attached to the door. Removed the drum (it came right off) wrapped the new belt around the drum, fed the belt through the tension flange and looped it over the pulley. Then rotated the drum a few times by hand to line everything up then put everything back together. It works fine now.

dryer drum would not spin

  • Customer: michael from North Platte, NE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the repair video on part-select. Pulled the top of the dryer up after removing the lint trap screws.removed screws at top, inside both sides and then lifted front off. Slipped belt over drum and ran through tensioner and around motor shaft. Put dryer back together in reverse order. Simple.

Tub would not turn

  • Customer: Lynn from Adel, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and performed as instructed- Could not have been easier- Great site with Great information

Broken Dryer Belt.

  • Customer: anthony from redmond, OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I came home from work to notice the dryer singing a different tune than usual. I opened the door and noticed that the tub wasnt turning. I popped the top of the dryer up to find a disentigrated belt. Fired up the computer and in a few minutes had ordered the $8 ($15 including shipping) replacement belt. 3 Days later took the shopvac and cleaned up the lint and broken belt pieces. Installed the new belt and was back in business with my 8 year old dryer. ** The only complaint comes from my wife who got her hopes up for a new front load washer and dryer** thanks partselect for saving my wallet in more than one way!

dryer ran 5-10min,then stopped until it cooled off

  • Customer: Leonard from Bayside, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Remove two screws on top holding the filter frame.Use flat screwdriver to snap top at front off front panel.Swing top up and secure it against wall or tie in place. Remove screws holding front panel and kick panel to side panels.Did'nt remove back panel.Remove drive belt from pully wheel and then use belt to lift out drum.Use open end wrench on motor pully at rear and I used a socket set on the front of motor,Push down on wrench,counter clockwise,and hold the front pully from moving mine came right off. My dryer is over 10 yrs so the electric conection was changed but the instruction sheet explained how to change the wires,just follow the wire color,easy.

Drum does not rotate, motor runs and it heats

  • Customer: Barry from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

Belt Broke

  • Customer: Dann from Granville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.
All Instructions for the KEYS850LQ0
1,021-1,035 of 1,179