Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KEYS750LQ2 > Instructions

KEYS750LQ2 KitchenAid Dryer - Instructions

All installation instructions for KEYS750LQ2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEYS750LQ2
1,786-1,800 of 2,035
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sqealing noise

  • Customer: Tom from Foxboro, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1) Watched the repair video to get familiar with the repair.
2) Disconnected the power.
3) Removed the bottom front panel and loosened the two bolts holding the top front panel/door
4) Removed the dryer belt from the tension pulley and motor
5) Removed the lint filter and two screws
6) Popped open the top of the dryer and rested it against the wall
7) Unhooked the two wires to the door switch and unclipped them from the front panel/door
8) Removed the two screws on the inside of the top front panel/door
9) Removed the top front panel/door while holding the drum
10) While holding the dryer belt, removed the drum
11) Loosened the bolt on the bottom of the left roller support
12) Removed the old metal retainer, plastic clips (both sides of the roller) and the roller on the left side
13) Removed the plastic clips and roller on the right side
14) On the right side, installed the new rear plastic clip, roller and front plastic clip
15) On the left side installed the new rear plastic clip, roller and front plastic clip. Then attached the roller support and new metal retainer. Then tightened bolt on the bottom of the support
16) Then put the new dryer belt on the drum, v-grooves facing the drum
17) Installed drum on new rollers and ensures rear felt strip was not kinked as I rolled the drum
18) Reinstalled front panel/door, installed inside screws, tightened bottom bolts and attached door switch wires
19) Followed directions to install new belt on tension pulley and motor
20) Rotated drum to ensure proper fit
21) Closed top cover and installed lint filter screws.
22) Re-installed bottom front panel
23) Connected power and ran dryer
24) VERY EASY!

door would not close

  • Customer: Daniel from Stratford, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.

Dryer seemed to overheat and would shut off

  • Customer: Kenneth L from Clearmont, WY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Changing the parts was very easy and took little time to replace all of the parts. I did watch the vidoes that where helpful. Troubleshooting the problem took more time than the repairs

Broken Belt

  • Customer: Joseph from Great Mills, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The belt broke at the worse possible time, with a washer full of wet clothing. Watched one of your fine repair videos, did exactly as it said and in less than 15 minutes I had the new belt on and the laundry continued as if nothing ever happened. Thank you for your help and instruction. I will continue to shop your site for all me maintenance and parts needs. Thanks again!

Broken Belt

  • Customer: Kent from Tallahassee, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was the first time that I'd had a dryer apart, so naturally I wound up taking many more things apart than I needed. After finally removing the front panel, I could see that the old belt had broken and was wrapped around the motor shaft, and that the tensioner was lying loose. Installing the new belt was a snap. Simply put it on the lines on the drum and insert into the pulley. The only challenge was figuring out exactly how the tensioner fit. The only way that it could go, and do its job, meant putting a lot of pressure on the spring. Once I got past that hesitation, it was a breeze.

Multi Rib Belt broken

  • Customer: Primoose from Grayson, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video on your site and it is very helpful and that is only I needed.

No heat

  • Customer: Jennifer from Hot Springs, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed broken element, replaced it with new element, reattached wires.

Broken drum belt

  • Customer: Jay from Lake Ariel, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After watching the repair video that was linked in the part delivery confirmation email, the repair went really easy. I just used the putty knife to pop the lid, then removed two sheet metal screws holding the front panel with the nut driver. I disconnected the two wires from the door switch. The front panel slid right up and out. The old belt was broken and lying at the bottom of the dryer. I ran the new belt around the drum, and around the tensioner and drive pulley. This was not as difficult as I imagined it would be. I spun the drum one revolution to make sure the belt was riding right. Before I put the front panel back on I took the opportunity to clean the lint out of the blower. I then just reversed the front panel removal process and snapped the lid back down. This repair took maybe 10 minutes. If I had to do it again I could probably do it in 5. It's just that easy. The dryer works perfectly now.

Broken heating element

  • Customer: Emery from Monroe, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed video. No problems with installation.Also was a good time to clean the dryer venting.

Dryer wouldn't turn on

  • Customer: Sharon from Jamestown, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Found Partselect, went to instant repairman read other peoples comments. I determined that I needed thermal fuse and thermal cut off kit. Ordered the parts early one morning, the parts came the next day. [Thank God!] I was expecting a long 3 to 5 business day wait. I watched the video to install. Took a few minutes to figure out about the jumper wire,[my dryer did not have the small wire] and low and behold, Grandma fixed the dryer saving herself a lot of money she needed to raise grandkids. Thank you so much!

Under heavy loads, dryer would turn off

  • Customer: Donald from Allentown, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Looked up on-line for tips, found computer animated video. It was easy as it looked, took longer to take dryer apart (not long). Other note on problem; neighbor who works on washer/dryers said that the motor was probably going. replaced belt anyway because I already purchased it before we spoken. Throwing caution to the wind!!

Drive Motor no longer working

  • Customer: Christopher from Cresson, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
I watched the informative video you sent via e-mail with order conformation. Installation was flawless. Thanks and will be using your site again for any other small appliance repairs that may need my attention.

took to long to dry, start button stop working

  • Customer: Barbara from Euclid, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband took the back off the dryer as instructed in the video and replace the heating element. To our dismay something else is wrong with the dryer. The start button still doesn't work. I know the heating element was needed because it stop drying at the normal temperature.

Belt had broken

  • Customer: George from Long Valley, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the online video three times. This was extremely useful. I just did what it showed. I doubt I could have fixed it without the video. This has got to be the best feature of the internet. I didn't have the exact model number, but the belt fit. I was surprised at how close the tensioning wheel was to the motor. Perhaps the belt will stretch with age and use.

Dryer Belt broke after about 10 years of use

  • Customer: Steven from West Point, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
We noticed the drum wasn't spinning, but the heat was turning on. About 3 years ago the heat was broken and it turned out that there was a little thermal fuse in there that needed swapped out, that was easy too fix too. Anyway, I looked up on youtube how to change out dryer belts on maytag units and it looked pretty straight forward. The model they showed was easier to access than my model, but I was able to still figure it out. Just pop off the top panel (they used a putty knife at the two clip points on the front, but I just yanked it up with a little force and it popped right up). Then unscrew the two little screws holding the front panel on, then pull off the front panel completely. This exposes the drum. The example on youtube showed easy front access to the belt assembly, but in my model, there was a stand for the drum as well as the drum motor in the way. So I just pulled the whole drum out the front most of the way, then I went behind the drum where I had exposed the pully/motor shaft assembly and then fed in the new belt into belt tension assembly that connects to the motor. While keeping it taught so the ribs of the belt would stay on the motor head (I had my wife hold it taught) I pushed the drum back toward the hanging belt and then worked the edges of the belt around the drum until it once again was completely around the drum. Then I slowly pushed the drum all the way back into place while continually working the belt back into place as I went. I then manually rolled the drum around a few times to ensure it was rolling correctly and that the belt was indeed in the right place. After a few good spins without it changing position, I reassembled the unit. It was very painless and took about 15-20 minutes in all. Works just fine again.
All Instructions for the KEYS750LQ2
1,786-1,800 of 2,035