Models > KEYS750LQ1 > Instructions

KEYS750LQ1 KitchenAid Dryer - Instructions

All installation instructions for KEYS750LQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEYS750LQ1
1,861-1,875 of 2,006
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken belt

  • Customer: Nicholas from Carnegie PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video instruction

Dryer would run for approximately 8 mins, then shut off by itself. After about 20 mins, dryer would restart but stop on it's own within 8-10 mins. Motor was also noisy when it ran.

  • Customer: Terrence from Hotsprings AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Unplugged dryer, removed 2 screws under filter lid, removed filter, removed access panel on back of machine, removed blower motor housing, vacuumed all dust and debris from rear of dryer, turned dryer around and opened top of dryer using a small screwdriver to release the clips approximately 2" from either end, then securing top from falling by using bailing wire to hold it in place, disconnected door switch wiring harness, removed 2- 5/16 screws retaining front panel and removed front panel from dryer, removed drum from dryer, removed idler pulley from bottom of cabinet noting position of drum belt, vacuumed dust and debris from bottom of cabinet and around old motor, removed motor retaining clips rotated motor and removed wiring harness from motor. I then attempted to remove the blower wheel from the old motor and here is where the problem began. If your dryer has the original motor in it, or the motor has never been changed in it to the best of your knowledge, go ahead and order a new blower wheel with your other parts, because you will not get the old one off without destroying it. (this cost me several days to complete the repair). Do not use channel locks or vice grips to attach to the front pulley to remove or install the blower wheel... use 2 medium sized crescent (adjustable) wrenches otherwise the pulley will be damaged and you will have a lot of filing to do to repair it. (If you need to reuse the pulley. I did not as my motor and pulley was an exact replacement). I got the blower wheel off of the old motor by using a chisel and a hammer and cutting a hole around the attachment point on the motor shaft from the rear of the dryer. After this, the job was pretty easy. I put the new motor in the motor housing, put a crescent wrench on the pulley on the front of the new motor, then screwed the new blower wheel onto the motor from the back of the dryer. (remember, the blower wheel has left handed threads, so to install it you have to turn the pulley on the motor to the LEFT to thread it into the wheel.) After the blower wheel is installed and hand tight, use 2 crescent wrenches to tighten down on motor, (1 on the blower wheel hub where it is square, and 1 on the front pulley) rotate the motor down to the correct position for the wiring loom, (you want the wires to rest on the bottom of the cabinet when the job is complete)., then reinstall the motor retaining clips and attach wiring harness. At this point I installed new drum rollers, reinstalled the drum with a new drum belt, and replaced the idler pulley with a new one. (push the drum counter clockwise by hand a few times to center the drum belt and to make sure that the drum is on the drum rollers correctly). The front panel is now reinstalled being careful to make sure the clips on the cabinet engage the holes in the panel. Push back on the drum slightly and reinstall the 2- 5/16 screws to hold the front panel to the cabinet, then reattach the wiring harness for the door switch. Remove the bailing wire and close the lid. The blower wheel housing is then reinstalled, then reinstall the rear access panel. Reinstall the filter and the 2 screws under the filter lid. Plug in the dryer and your repair is complete. When a motor replacement is required, you are better off replacing the motor, blower wheel, drum rollers, drum belt, and idler pulley. I did and my dryer sounds and performs like a new one. My wife is absolutely delighted. I spent approximately $180.00 on the total repair while a new dryer would have cost me $600.00 + tax.

tumbler would not turn

  • Customer: LORRIE from ARNOLD PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the video directions exactly as instructed and I had no problem doing the repair myself. And if I can do it being a woman with no help you can do it. Easy peasy~

Sqealing noise and extended drying time

  • Customer: Gregory from Casa Grande AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed online youtube directiond to dissassemble dryer cabinet. Everything is readily accessible and belt and idler are easily installed. Comments from others express frustration at the instability of the idler pulley bracket. The key is to keep seating pressure on bracket until the belt is installed at which time the belt supplies continuous pressure to seat the bracket. The bracket is very stable so long as moderate force is applied to hold the brackett in the seat. The belt install is counter intuitive in that the ribbed side of the belt is installed in contact with the drum instead of the flat side. The readon for this is so the belt ribs seat in the grooves of the motor pully and provide greater friction. Flat side of the belt on the drum places the flat belt on the grooved pulley with much reduced contact area.

my dryer stopped tumbling

  • Customer: joann from woonsocket RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
so being the WOMAN that I am I decided to take it apart. well low and behold I found out it was the pulley and belt so I decide too order from parts select easiest thing I've ever done yay me

Dryer making squiling noise when on.

  • Customer: Jerry from Magnolia TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First I watched a instruction video online.. It made the job easy. I have done it before but I did not remember exactly how to proceed, After watching the video i knew exactly what screws needed to be removed and what tool I needed for each step. Anybody sees the video before tackling this job, they can't go wrong.

Drum stopped turning

  • Customer: james from blue point NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After removing the back, I realized I absolutely did not know what I was doing. I went to google put in my model number, and went to your web page. The rest is history. Went to the video watched it and went back to the dryer and after cleaning up the back, put it back and removed the top and front as per video. The parts came in a few days and replaced the belt and idler arm n about 2 min. I am not kidding. The wife held the drum while I put the front back on. One thing I could not separate the door switch so I just unscrewed it from the fron panel. The dryeris 20 years old, and your web page will put the Maytag repairman on the unemployment line.

Dryer had become REALLY noisy.

  • Customer: William from Dallas TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The PartsSelect video was great. I'm not sure I would have figured out the trick for opening up this dryer without it. After that the main problem was getting goop off of the drum support roller spindles. This took lots of solvent and elbow grease. I think this was the main source of noise. The oil had turned to something like partly dried glue. They were very hard to turn. The belt was intact but badly cracked. The idler probably could have been oiled and reused but I already had the part so I replaced it. Everything went just like the video. The dryer now hums along like a new one!

Dryer would not run

  • Customer: Joe from Harrisburg PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

blower wheel cracked and broke

  • Customer: Kellie from Norton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

dryer stop running.

  • Customer: Sophia from Farmington NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
My son worked on the dryer it was easy for him he just followed the instruct that came with the order. My dryer is like new now and didn't to buy a new one way cheaper save me a lot of money. Thank you.

Broken Blower Wheel

  • Customer: James from Mosca CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.

  • Customer: Dale from Joanna SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

i had difficult time getting wheel off.

  • Customer: dwight from monticello AR
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
found out that pushing in on wheel and turning counter clock wise, wheel screws off rather easy.

Dryer wouldn't start... Just a hum when you press the start button.

  • Customer: James from Festus MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Well it took me longer to get the dryer apart and than it did to get it back together... Well I opened it up it was obvious I had burned up the motor you couldn't even see it for all the lint that was built up around it... And the hardest part was removing the fan from the motor shaft, I didn't realize it was plastic and sort of mangled it getting it off so I went ahead and replaced it as well. The hardest part of the whole repair was removing and replacing the clips that hold the motor in place and there didn't seem to be any trick to it, I used a pair of channel locks and a little muscle to get them off and back on everything else was a breeze! I recommend checking the exhaust pipe at least once a year to make sure air is flowing freely to prevent the lint build up inside and even more often if you have a long run. This should prevent having this problem again...
All Instructions for the KEYS750LQ1
1,861-1,875 of 2,006