Models > KEYS750LQ0 > Instructions

KEYS750LQ0 KitchenAid Dryer - Instructions

All installation instructions for KEYS750LQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEYS750LQ0
31-45 of 2,006
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door switch did absolutely nothing....dryer kept running

  • Customer: Clark from Melbourne FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 82 of 146 people found this instruction helpful
I read a fix-it article from another contributor and followed those instructions to the T. Pull out lint trap, remove the two screws. Slide the top cover towards the front and prop it up with a mop handle.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.

door kept coming open dryer shuts off

  • Customer: RONALD from SALMON ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 80 of 143 people found this instruction helpful
use screwdriver topry plastic out plyers to pull out metal latch put new parts in

Broken Switch Assembly

  • Customer: Michael from Dearborn MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 77 of 138 people found this instruction helpful
This was my first dryer repair, and it was so easy. Simply pull out the lint trap and unscrew the two screws that are exposed. They attach the top deck of the dryer to the drum.

Once it's unscrewed, pull forward while lifting the top of the dryer. The top is attached to the control assembly. They should both lift up, but you'll need something to prop it up like you would the hood of your car.

Next, use the pliers to pinch the connector so that you can separate the two parts of the connector.

Open the dryer door to gain access to the screws that hold the switch in place. Use your screwdriver to unscrew the switch.

Plug the new switch connector in, and close up the dryer.

Word of caution; there are sharp edges inside the dryer so be careful.

Door won't latch

  • Customer: Jill from bellevue WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 75 of 133 people found this instruction helpful
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

no heat

  • Customer: kat from powell OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 48 of 57 people found this instruction helpful
First, I replaced the heating element which was super easy but I still didn't have heat - frustrating! I then ordered the thermal cut-off kit and thermal fuse. I replaced the thermal fuse and still no heat. Then, I took one of the fuses from the kit and replaced that and finally got heat. There was another fuse in this kit that I still don't know where it goes but right now I don't need it. Had I known (by a volt tester) this would have been super easy to fix, but I didn't have one so it was trial and error. I did find out, however, that if the heating element goes it usually takes the fuse with it. The fuse I replaced (that finally gave me heat) was located in the casing just above the element. I hope this helps!

Dryer would not start.

  • Customer: Clarence from Davison MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 46 of 54 people found this instruction helpful
Hard part was to figure out which part was bad. Checked out all thermo OL and fuses. The start button was only thing left. To change, take off back cover. Pull off knob from front. Pull off wire connector. From the back, pull back the top locking tab and rotate switch 25 degrees. Part fits into a square hole. Reassemble.

Broken belt - drum would not turn

  • Customer: Gary from Oakland MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 43 of 47 people found this instruction helpful
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcerting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.

No heat,thumping when running

  • Customer: Herbert from Holley NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 44 of 61 people found this instruction helpful
Removed front panel, drum,replaced belt,tensioner and worn rollers. Then removed rear panel and replaced heating element and high limit thermostat. While I was there completely cleaned inside of dryer. Repair and replacement of parts was quite easy. Just take your time and don't hurry it.

worn out lint filter

  • Customer: gregg from castaic CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 34 of 37 people found this instruction helpful
The new lint filter fits perfectly,however because the handle is much larger than the original it does not allow the filter to close completely...causing a small amount of lint to acummulate on the dryer top.

Bought motor, then bought blower wheel also

  • Customer: Daniel from Coatesville PA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 38 of 49 people found this instruction helpful
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!

Dryer motor would not turn on

  • Customer: John from Bluffton SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 32 of 34 people found this instruction helpful
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.

Replacing worn drum support rollers and shafts.

  • Customer: Gary from Canton CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 32 of 35 people found this instruction helpful
Very easy once I figured out how to open it up to see what was the matter.
1 Remove power.
2 Open the lint filter cover and remove the 2 Phillip screws.
3 Pry the front of the top cover up to separate the cover from the plastic clips that secure to the top front panel.
4 Remove the 2 nut screws securing the top of the front panel to each side cover.
5 Pull front panel out slightly to detach wiring from the cover switch.
6 Pull front panel straight up and set aside.
7 Remove drum belt from tensioner and motor pulley under the drum.
8 Remove drum by pulling it toward the front between the 2 sides.
9 Locate the 2 support rollers and their mounting shafts. Change the shafts at this point if they are worn. (Mine were OK)
10 Remove the support bracket from the shaft if present.
11 Remove the plastic triangular retainer from the shaft and slide the old wheel off of the shaft.
12 Clean the shaft from any bearing debris.
13 Replace the rollers and retainers.
14 Insert drum through the front side panels making sure the seal on the rear of the drum is centered around the opening and not folded inside the opening.
15 Place the belt on the drum and thread the belt through the tensioner and around the motor pulley.
16 Position the front cover on the lower clips on each of the sides.
17 Re-attach the 2 wires for the cover switch.
18 Pull the drum up so the opening on the drum and front cover align.
19 Screw together the side panels to the front panel using the 2 hex headed screws.
20 Check for binds by rotating the drum several times by hand.
21 Press the front of the top panel down toward the front panel to engage the plastic clips attaching the top to the front. Watch for the lint filter housing alignment as you push the top panel down.
22 Replace the 2 screws to attach the lint filter to the top cover.
23 Plug in machine and test.

Good luck, It s not as bad as it sounds.

Rear Dryer Seal was old and staining clothing

  • Customer: Grace from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 30 of 31 people found this instruction helpful
After unplugging the dryer,I removed 2 bolts on the back top of the dryer, then removed the two screws in the lint box area. I used a screw driver to help force the top panel of the dryer up. When open, I removed the top screws that held the front and side panels together. I then lifted the front panel up and away from the dryer, so there would be room to take the drum out. I removed the belt from the pulley (located under the drum) and slid the drum out. I removed the old seal, cleaned up the drum and the inside of the dryer, then glued the new seal on. After the glue was dry, I put the drum back in (with the belt on the drum), put the belt back on the pulley and proceeded to put the dryer front back on. Once the front was on, I put the top back on and replaced the bolts on the back of the dryer. I plugged it in and it is working great! By the way, before this, I had NEVER attempted to repair a dryer before and I am female. If I could do it, so can anyone else willing to try :)

Dryer making extra noise while running

  • Customer: Michael from Haines City FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 31 of 36 people found this instruction helpful
1st Unpluged power.
2nd removed two screws under lint screen cover.
3rd poped up lid with flathead screwdryer, then removed (2) 5/16 screws from door cover and unpluged lid switch, lifted up dryer door pannel
4th removed drum
5th took out plastic triangle wheel rings
6th removed old belt guild (to motor pully)
7th removed old wheels and plastic rings stops
8th cleaned excessive hair dust with shopvac
9th put new replaicment part in dryer. made sure to turn manually to make sure belt was lined up properly, then put all dryer peices back.
10th aditional work, took back cover off and removed the (4) 1/4 screws for lint screen case (left side in dryer) vacumed out any excessive dirt lint ect, also cleaned any excessive dust I found in back of dryer, dryer , exhaust ect, and put all back together.
JUst like a new dryer aain after all PM was complete.

drum stopped turning on dryer

  • Customer: Matthew from East Islip NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 29 of 35 people found this instruction helpful
Great! Spent about $36.00 and I ended up with a overhauled dryer. I ended up cleaning the whole thing out, it's amazing how much stuff accummulates in the frame of a dryer, I also found about $2.00 in change. It's a good idea to clean out a dryer every few years and the broken belt forced me to do it.
But anyway the parts cam very quick and had easy to follow directions.
I would reccomend part select. Matt
All Instructions for the KEYS750LQ0
31-45 of 2,006