Models > KEYS750LQ0 > Instructions

KEYS750LQ0 KitchenAid Dryer - Instructions

All installation instructions for KEYS750LQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEYS750LQ0
1,786-1,800 of 2,006
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the lint chute assembly had corroded & would not accept the lint screen.

  • Customer: Richard from Paramount CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I pulled thee dryer out from the wall, shut off the gas & disconnected the gas line & the air vent, I then removed the fasteners from the upper end of the lint chute assembly (accessible from the top of the machine). I then tipped the machine over on to its front side making the back fully accessible. After removing the back cover, I removed the remaining fasteners holding the lint chute assembly in place & removed the part. I then removed the assembly only to find that the seals were not included in the package even though I had specifically asked about the seal when I called in & place my order. The response to my question was " seals are included that is why it is called an assembly." The end result was that I had to use alternate material & fabricate my own seals in order to complete the installation. As a result a repair which should have taken no more that 30 minutes, took over two hours.

would not heat up enough

  • Customer: Carol from Minneola KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed troubleshoot & repair steps provided by partselect.

Dryer would not start.

  • Customer: Sam from JOHNSON CITY TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took back panel off. Did not have a clue! Went to Partselect Web site,entered my problem,BAM! instant solution.Watched repair video and was surprised how simple repair looked.Heck I can do this,no problem! I work from 7 A.M. to 5 P.M. so theres no chance to stop by local appliance part store before they close. Ordered my parts from Partsselect,arrived in just two days. Followed video instructions ,completed job in thirty minutes or less! I also got important information regarding maintenance and cleaning dryer to prevent fire hazard.Thanks,for help and saving me time and money.When I have a problem in the future I now know where to go.

No heat/timer wouldn't shut off.

  • Customer: Jay from Georgetown IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled the back off, removed heating element and thermostat, installed new heating element and thermostat. This didn't fix my problem. Now I'm not sure what to do. I watched a video on diagnosing the problem on youtube. It helped me install the parts I bought. Now I'm not sure what the problem is as the ones I bought and installed didn't fix the problem. I guess diagnosing is my problem now.

Drum stopped turning

  • Customer: David from Jamestown RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.

Drum not rotating

  • Customer: Chris from Sayrevlle NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.

Lould nosie from Drum Whells

  • Customer: FRANCIS from PHILADELPHIA PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch and followed the three viedos that PartSelect emailed me and had a very easy repair job.

Broken belt and bent idler pulley

  • Customer: Mollie from Walterboro SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First unplug the unit. Take the lint filter out and remove the two Phillips-head screws at the edge of the opening. Then using the putty knife to unlatch the top panel of the dryer, insert it into the seam on the front about 3" from each side. When you feel the knife up-against the latch, apply a little inward pressure with the knife and pull up on the top panel. When you release both sides the panel, it will lift up and back against the wall(secure it so it doesn't fall forward while you are doing this repair). Looking down on the right-front corner you will find a connection for the door switch, Dis-connect it. Just below that connection, on the inside, is a 5/16" screw that holds the front panel on, take that one and another one just like it on the left side, out and the front will fall forward about an inch and then you will lift up on the panel while holding drum in place. Inspect the clips that hold the bottom of the panel on and be aware how the panel attaches to them. Try to keep the drum in place and set the front panel off to the side so you can easily grab it to put it back on. Looking under the drum remove the belt and idler pulley. The pulley is usually not in the position it should be in, it likes to fall over when it has no belt pressure on it. Hopefully you had already unpackaged the new belt and straightened it out. Loop the belt over the drum, rib side to the drum, and move it to where the old belt had been riding on the drum. Back under the drum, you should hold it in place with your shoulder, with idler pulley in hand-- install the idler pulley. There's probable a clean spot where the old one was and the humpback should point to the right side of the dryer. With right hand steadying the idler pulley, the left hand should pinch the belt together and feed it under the wheel and pull it out and hook it on the motor pulley. It may seem to be a tight fit but once its on you should be able grab the outside edge of the drum and slowly turn it without hearing any scraping noises. Double check that the belt isn't twisted. Before putting the front panel back on or if you had to take the drum out, make sure the felt seal on the back edge of the drum is not folded inward. the wheels that the drum roll on must be in the groove. Carefully reach to the back to check that they are in the groove of the drum. If everything seems to be in place, hold the drum with one hand and grab the front panel with other. Place the bottom of the panel against the unit and lift up about an inch and place the square holes at the bottom of the panel on the clips on the unit, it may take a couple of tries, then lean the panel forward making sure the drum goes around the felt seal on the panel. Once the panel is against the unit , install the two 5/16 screws securing the front panel to the unit. Turn the drum by hand to make sure drum was installed properly. Reconnect door switch. Lower top panel and push down to secure it. Install the two Phillips head screws at the edge of where the lint screen goes, install lent screen and plug the unit back into the wall socket.

Door switch hadn't been working for a while and when the belt broke decided to make it right.

  • Customer: Martin from Saylorsburg PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed front and replaced belt,idler pulley and door switch. Was an easy repair.

Belt & clip where both broken

  • Customer: Amy from Seagrove NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
My 11 year old son and I ordered the parts we needed. Saw the GREAT easy installation video, It even was attached to my confirmation. After the parts got here him and I easily took off the old belt and clip, installed the new ones (after watching the viedo again) and we where done. You would have thought we fixed the space shuttle or something because we both smiled all day. My son also told every one that he and his mom fixed the dryer all by ourselves. Costed me only $40 dollars for the parts. I couldn't have even called a repair man out there for that. Thanks soo much.

drum not turning

  • Customer: Tony from Greenville IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched a video on utube and realized how easy this looked, took my dryer apart to see the belt broken in half and the idler pulley in pieces. Found Partselect on the internet and ordered my parts. Partselect was awsome, website was easy to navigate, ordered my parts and they were at my house the very next day and were the correct parts. Cleaned all the lint and dust out of the inside of my machine, installed new parts and put it back together. Works great and is still running strong. A service call, plus parts (with thier mark up) could have easily been $150.00 - $200.00 dollars. this repair was complete in about an hour and only cost me $37.50

Squeaky Idler Pulley

  • Customer: Mitchell A. from Hampton NH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video that showed how to do the repair. I did exactly what I was shown on the video, and everything worked the very first time ! It was GREAT ! No more squeaking idle pulley !

drum was not turning

  • Customer: John from West Islip NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your video and did the job,really no problem. I also cleaned out all the lint and dust will the drum and front were out.

drum not spinning when dryer on

  • Customer: Joseph from Red Hook NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The removal of the front door assy was very easy after I popped up the top cover with a putty knife.Once removed it was easier to replace belt and idler assy with dryer on its backside.the only trick was to get looped thru idler roller and then fasten bracket in slot on bottom of dryer.also the instructions were well written which made re-assy much simplier.

Motor noise followed by shutdown

  • Customer: Richard from Oceanside CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Before placing your order remove the motor. At the rear of the motor is a plastic nut which is how the fan is attached. Mine was stuck and needed to be removed with a cutoff wheel from the back side of the dryer. This delayed the project several more days as I had already received the motor before figuring out the fan was stuck.
All Instructions for the KEYS750LQ0
1,786-1,800 of 2,006