KEYS700JQ0 KitchenAid Dryer - Instructions

took the back of the control panel off and pulled the Push to start switch off, put the new one on and replaced the back panel.

My husband who is in a wheelchair and his freind who had never worked on a dryer,watched the video online and boom! just like that it was fixed!Some nut told me it would cost too much to fix,To just get a new one!Boy am I grateful for you!Thank You.virginia.

First and foremost, PartSelect is awesome! I placed the order on a Monday afternoon with regular shipping, and I had the belt Tuesday evening. Total repair involved removing several screws to open the top and front of the dryer, then installing the new belt. Pay close attention to the the dryer seal - make sure this is completely set. This was a very, very easy repair, and it cost me less than $20 for part and shipping! Also, the video on the PartSelect site shows exactly how to make this repair, and was very helpful.

Un plug the Elect. The two screws that hold the lent screen in place and the top. I took them out and I used a putty knife to open the top of the dry. un plug the switch And take out the two screws under the switch. That was all too it. Just like the instructor said .

Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Unplug Dryer. Take off exhaust hose. Unscrewed the back panel and remove off the dryer. Locate heating element and unhook wires. Unscrew heating element. Replace with new heating element. Hook up wires. replace panel and exhaust hose. Plug dryer back in. Check for heating.

Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

I checked all of the most commonly affected parts (as described on this site) with an ohmmeter (My first time but very easy to use). The only exception was the heating coil but this appeared to be working fine. The cycling thermostat showed resistance so I ordered a new one here. Replaced it and now the drying is working like new! The informational youtubes, diagnosis, purchase and repair only took me an hour. Never tried fixing an appliance myself before but so satisfying! $25 dollars and convenient timing is much better than the $350 I spent to have an appliance repairman fix my washer.

follow video and fix.

Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

Followed the instructions on the video

The video instructions here were exact and very clear. I replaced the door switch but that did not fix the issue. I used the instant repair man tool and found that the next most likely part to have an issue was a the thermal fuse. After replacing that part which took 10 minutes... It works! My part was shipped to my home very very quickly. totally worth it.

Very easily replaced both parts. Works perfect!!

I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.