KEYL507WWH0 KitchenAid Dryer - Instructions

I first examined the electrical diagram that came on the inside of the rear panel to determine where to check for loss voltage since this problem had all the tale,tale signs of a device not receiving power to turn on so I began at one end of the circuit and using my Fluke meter on the AC scale along with the electrical diagram found the thermal fuse opened.At that time I went to your site to see if I could buy this part and found you had it plus more so even though the thermo switch tested good I felt the need to replace it along with the thermo fuse as a set. I'm an electronic tech for a different type of machines but this was still just an electrical problem like the machines I work on daily.

Checked the element and switches. Found thermal cut off switch open. Order new switch. Installed switch and vacuumed cabinet. Start and test.

I felt the belt had broken since the unit was still running. I went on-line looked at some you tube movies to get some idea what to do. Was very helpfull. Found on-line how to get the part forb this nearly 20 year old dryer. Had the part shipped overnight, was able to track it. Followed your innstallation instruction, With the heavy rubber bands hooks at both ends it was easy. Never done this before, sure saved a good amount of money.

Per the electrical diagram that was in the dryer , using a VOLT OHMETER I found the thermal fuse was open. Then ordered the part , arrived the NEXT DAY via Standard Shipping. Easy to replace .

First off, I ordered the part around 1 pm, paid regular shipping, and it was here the very next day! As for the repair, maybe the easiest fix I have done. Make sure the dryer is unplugged, pop the top up and remove the front of the dryer. Take out the pulley (careful it can snap ya) then remove the drum. The snap rings around the motor can be tricky, so be sure to watch the video sent to you from PartSelect. With a couple of wrenches, loosen the motor from the blower and remove. Put new one in and put back together. Piece of cake. Took me about 20-25 mins. This is the best place I've ordered from and will continue to get my supplies here. Good Luck!

This dryer refuses to die and I am happy to keep it that way. Door latch was replaced in less than a minute using this kit. Easiest repair ever.

After looking at your video, my brother and I put the belt back on, placed the front and back on and that was it. It required two of us but it went well and the machine is working fine. Thank you.

followed the video instruction

took top off,took back off,took lower panel off,removed old motor without taking drum out,got the part # off old motor,looked it up on line then i found the video on how to do the repair...lol. The repair went well and the instructions that came with the new motor were very good as my motor had the old style switch and needed to be rewired. I did go one step further as long as i had it that far apart,I took the duct work apart on the back of the dryer for the vent and I was very glad I did,it had 25 years of lint and all sorts of other thing in it.I cleaned and lubed all other moving parts and reassembled,works and sounds like new !

Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.

The belt broke at the worse possible time, with a washer full of wet clothing. Watched one of your fine repair videos, did exactly as it said and in less than 15 minutes I had the new belt on and the laundry continued as if nothing ever happened. Thank you for your help and instruction. I will continue to shop your site for all me maintenance and parts needs. Thanks again!

This was the first time that I'd had a dryer apart, so naturally I wound up taking many more things apart than I needed. After finally removing the front panel, I could see that the old belt had broken and was wrapped around the motor shaft, and that the tensioner was lying loose. Installing the new belt was a snap. Simply put it on the lines on the drum and insert into the pulley. The only challenge was figuring out exactly how the tensioner fit. The only way that it could go, and do its job, meant putting a lot of pressure on the spring. Once I got past that hesitation, it was a breeze.

Watch the video on your site and it is very helpful and that is only I needed.

After watching the repair video that was linked in the part delivery confirmation email, the repair went really easy. I just used the putty knife to pop the lid, then removed two sheet metal screws holding the front panel with the nut driver. I disconnected the two wires from the door switch. The front panel slid right up and out. The old belt was broken and lying at the bottom of the dryer. I ran the new belt around the drum, and around the tensioner and drive pulley. This was not as difficult as I imagined it would be. I spun the drum one revolution to make sure the belt was riding right. Before I put the front panel back on I took the opportunity to clean the lint out of the blower. I then just reversed the front panel removal process and snapped the lid back down. This repair took maybe 10 minutes. If I had to do it again I could probably do it in 5. It's just that easy. The dryer works perfectly now.

Looked up on-line for tips, found computer animated video. It was easy as it looked, took longer to take dryer apart (not long). Other note on problem; neighbor who works on washer/dryers said that the motor was probably going. replaced belt anyway because I already purchased it before we spoken. Throwing caution to the wind!!