Models > KEYL410BAL2

KEYL410BAL2 KitchenAid Dryer - Overview

Get Parts and Repair Help for KEYL410BAL2

If you know the dryer repair part you need, you can browse the list of all parts on the KEYL410BAL2, or you can search by name or part description. You can also find your part by where it is located on the KEYL410BAL2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for KEYL410BAL2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the KEYL410BAL2 [Viewing 3 of 3]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.11

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

Order within the next 11 hrs and your part ships today!
$11.97

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

Order within the next 11 hrs and your part ships today!
$14.09

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenh...

Order within the next 11 hrs and your part ships today!
$28.84

Thermal Cut-Off Kit

This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.

Order within the next 11 hrs and your part ships today!
$4.14

Door Catch Kit

This kit contains two door strikes, and various door catches to service dryer doors that have one or two catches.

Order within the next 11 hrs and your part ships today!
$10.71

Drum Support Roller

Sold Individually. Most dryers require 2. Tri-rings sold separately.

Order within the next 11 hrs and your part ships today!
$23.20

Lint Filter with Handle

This filter collects lint as it passes through the dryer vent.

Order within the next 11 hrs and your part ships today!
$4.54

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 11 hrs and your part ships today!
$3.54

Leveling Foot

Sold individually.

Order within the next 11 hrs and your part ships today!
$10.45

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1373 of 1570 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No Heat

  • Customer: Vernon from Niceville FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 609 of 632 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more

Dryer tub belt broke

  • Customer: Ray from Denton TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 606 of 641 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more