Models > KEYE770BAL2

KEYE770BAL2 KitchenAid Dryer - Overview

Get Parts and Repair Help for KEYE770BAL2

If you know the dryer repair part you need, you can browse the list of all parts on the KEYE770BAL2, or you can search by name or part description. You can also find your part by where it is located on the KEYE770BAL2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for KEYE770BAL2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the KEYE770BAL2 [Viewing 3 of 3]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.20

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

$14.08

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$14.60

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenh...

$34.70

Thermal Cut-Off Kit

This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.

$2.82

Light Bulb - 40W

Sold individually.

$4.76

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$16.36

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

$32.95

Lint Filter

This dryer lint screen comes with a handle. This filter collects lint as it passes through the dryer vent.

$3.66

Leveling Foot

Sold individually.

$6.68

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 805 of 936 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

Dryer tub belt broke

  • Customer: Ray from Denton TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 407 of 429 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more

heating coil was'nt heating up and after i change the coil realize the little thermal regulator had to also be change.

  • Customer: Rube from Houston TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 387 of 406 people found this instruction helpful
I basically took the back offo the drive, then detach
the heating coil. Afterwards had to go back in and
change the thermal regulator an the job was completed. read more