KEYE760WAL0 KitchenAid Dryer - Instructions

open machine up and replaced the new belt.

just removed old fuse and installed new one ..... cleaned all the vents out to

It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

I am one Happy Gal.....Looked to fix,thought about just buying a new dryer..In the end talked to the local repair guy...said I could do it myself. (why pay him)..I live in small town.Ordered your part,watched the video and did it...Saved myself over $500, plus the $125 for delivery.for that new dryer..(Small town in the forest!)Very easy to install....Hope to use this dryer for many months perhaps years..It is 30 years old! Works like a champ! Thank You!

just took off the front panel took off the belt and replaced it with the new one we watched the video pretty easy

Diagnosed the problem on parts select, ordered the part and watched the youtube video on how to install and done! Super easy - thanks for boosting my "chicks can fix anything" mojo and saving me a bunch of $$.

More time troubleshooting than repairing. Used online help for narrowing down problem to the thermal cut-off unit. Had to remove front lower cover, remove wire sets from heating element,remove element from dryer. Then it was a simple swap out of the two relays/thermistors, and put it all back together again. Unit worked as designed after repair.

Saw no heat, web said probably the fuse. Replaced the fuse. Nope. Second guess was the thermostat at the exhaust. Replaced that. Nope. Finally got to actively troubleshooting and isolated one of the thermostats near the heating element. Replaced that and everything is fine. So now I have a good spare fuse and thermostat for the next repair. There was one tool I wished I had, a socket small enough to open the back. I had to use pliers and that was a pain. Other than that the repair was almost trivial, just unplug the bad one and plug in the good one.

Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.

Removed back panel of the dryer and located the thermal fuse. Disconnected two wires, and removed one screw holding the fuse in place. Installed new fuse and reassembled. Dryer works like a champ again.

Disconnect the power cord. Unhook the dryer vent hose. Remove the back. Find the Thermal Fuse. Use a ratchet and socket to remove socket head screw that holds the Thermal Fuse in place. Disconnect one of the two wires from the old Thermal Fuse and attach the wire to the new Thermal Fuse ensuring the wire is placed on the same end of the new Thermal Fuse as the old Thermal Fuse. Repeat procedure for the remaining wire and screw Thermal Fuse back in place. Replace the back, reattach the dryer vent hose and connect the power cord.

The on-line instructions were excellent; however, the man doing the demonstration used a brand new machine - not one where the old seals had melted and dried out and required serious cleaning before attaching the new seals. The new seals went on easily and I am very happy with everything about this task. I am also glad I now know what that lint chute looks like, so I'll do a better job of keeping it clean in the future.

Pulled up a You-Tube vid on how to install the belt. Went perfect.

I knew I needed a thermostat. So that part of the repair was my contribution.

i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.