KEYE677BWH2 KitchenAid Dryer - Instructions

Upon receiving the parts from Parts Select I reviewed the contents of the package and then compared with what i had ordered. I then reviewed the video to locate the part and to ensure correct dis-assembly and installation. I had no problem with the new installation once I sorted out the wiring. Th PS video for this model describes and shows three red or orange wires coming for the harness two standard and on e thin wire which goes to the thermal cut-off. In my dryer this orange or red wire was actually bland white striped. I called PS who suggested I call Whirlpool who also could not help and insisted that this model had an orange wire where I was describing it as black, the concern was was that with this new thermal cut-off wires had to be cut and fitted with new ends to accommodate a change in design. I therefore did a little temporary wiring t before I cut any wires to ensure my assessment was correct. I was then able to cut the black and white wire fit it with a new end and plug it into the double connector that was now fitted to the jumper cable. I the connected the double connector to the thermal cut-off and tested the dryer for heat. I re-fitted the back panel and re-positioned the dryer to present everything is working satisfactorily. I would comment that someone needs to check why my dryer had a black and whit cable coming from the harness when both Whirlpool and the PS video show it as orange/red.

replaced fuse great website

We got this dryer from my F-I-L after they had to enter an elderly home. My F-I-L was a modern Tim-Tool-Man-Tyler. He had removed most of the protections and installed a 392 Thermal cut off, I guess he wanted to dry his cloths in 30 seconds or less. I was not aware of this, and used the dryer. Yes you guessed it, we sat it for a 30 minute cycle and it blew the cut-off and melted the wiring. I am a degree/certified computer tech so I fixed it myself, but I hate 220 electricity. Need less to say I checked with this site for the OEM parts and they pointed me in the correct direction. I did have to remake some of the wires since they were crisp, but it all went well and it was easy enough. The lesson, companies install OEM parts for a GOOD reason, best always to follow the makers directions.

As per online video instruction. Easy as pie...

unhinged top panel. removed front panel. installed belt and reinstalled front and top panel.

Got the part in 2 days, fixed it. Thanks

Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Unplug Dryer. Take off exhaust hose. Unscrewed the back panel and remove off the dryer. Locate heating element and unhook wires. Unscrew heating element. Replace with new heating element. Hook up wires. replace panel and exhaust hose. Plug dryer back in. Check for heating.

Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

I checked all of the most commonly affected parts (as described on this site) with an ohmmeter (My first time but very easy to use). The only exception was the heating coil but this appeared to be working fine. The cycling thermostat showed resistance so I ordered a new one here. Replaced it and now the drying is working like new! The informational youtubes, diagnosis, purchase and repair only took me an hour. Never tried fixing an appliance myself before but so satisfying! $25 dollars and convenient timing is much better than the $350 I spent to have an appliance repairman fix my washer.

follow video and fix.

Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

Followed the instructions on the video

Very easily replaced both parts. Works perfect!!

I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!