KEYE664WWH1 KitchenAid Dryer - Instructions

The broken belt was found when I opened the dryer. The part number was on the belt and a quick online search led me to PartSelect. The part was available, delivered in less than 2 days and there was an online video showing the entire repair in detail.

Step 1: remove new latch from bag in which part comes. Step 2: push latch into hole where the other latch was. Step 3: enjoy having a dryer you dont have to hold closed with a folding chair.

Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

I checked all of the most commonly affected parts (as described on this site) with an ohmmeter (My first time but very easy to use). The only exception was the heating coil but this appeared to be working fine. The cycling thermostat showed resistance so I ordered a new one here. Replaced it and now the drying is working like new! The informational youtubes, diagnosis, purchase and repair only took me an hour. Never tried fixing an appliance myself before but so satisfying! $25 dollars and convenient timing is much better than the $350 I spent to have an appliance repairman fix my washer.

follow video and fix.

Could not be any easier. For less than $20 and 15 minutes time, I couldnt be happier.
All that was needed is a nutdriver to remove a 1/2 dozen screws to take the back panel off. Then a phillips screw driver to remove the thermal fuse. Unplug 2 wires and then attach them to the new fuse. Put it all back together and done!. Working dryer.
PS: I had enough gas line and ducting connected to the dryer ,so thatt I was able to get behind it with out removing them. This may have taken another 15 min. if I needed to do this and two adjustable wrenches.

Very easily replaced both parts. Works perfect!!

I lifted the top of the dryer. I unhooked the hangers from the door and took it off. I pulled the drum out, took the broken belt off, slid the new one around the outside middle of the drum, turning the rib side of the belt out,and ran the belt through the pulley attached to the bottom base of the dryer (tension pulley, right hand side), slid the drum back inside the dryer frame, reattached the door, closed and snapped the dryer lid and it worked great!!

Your customer service was great, but your video wasn't particularly helpful because of the extreme age of my dryer. For one thing, with these really old dryers, you don't have to slide the drum out at all; you just unscrew the front panel and slip the belt in that way. The printed diagram that came with the belt helped me figure how the belt slips through the pulley assembly, but the drawing could have been more clear. In spite of my bickering, I probably saved $50 fixing it myself.

Disconnect electric power, the top & cabinet are connected by 2 reusable locks about 4 inches from each front corner, use a thin flat putty knife or similar object, push inward on a lock while lifting gently on the front of the top piece, then let the top rest against the wall. ( a wire on each end of a safety switch for the dryer door may need disconnected) Remove a screw from each front corner of the cabinet, then pull upward on the loose front panel to access the drive motor, remove old belt. install new belt by lifting the front of the drum just high enough to allow the new belt, place groves of belt against the drum and around the motor pulley and belt tensioner, re-install cabinet front, (re-connect safety switch wires) return top and push down at cabinet locks.

I took one piece off at a Time. Made sure that each wire went to the correct place. I felt so good as a woman to be able to fix a necessity in our House without having to call a repairman to fix it for us. We are 3 women in our New Home. Im 46 My life partner is 48 and Our Daughter 17. I can't tell you how thankful i am for watching your video on how to do it. Thanks Part select. Dena , Ave & Fe .

I checked the thermal fuse for continuity and had none.ordered part arrived next day. I took a picture with phone to idenify wires. installed in a short time.dryer works like new

I watched the videos associated with the parts. They were easy to understand and I could follow the steps without difficulty. I replaced both the cycling thermostat and thermal fuse. Separately, I also replaced the "push-to-start" switch. Dryer would still not start. I called the repairman. Problem turned out to be a loose wire that had shorted out in the electrical bar near the "push-to-start" switch. All parts I replaced are determined to be good and will be tried next time I experience the dryer "not starting".

Unpluged dryer first! Diconnected the vent hose.Took out 9 screws out of back panel.1 screw for the thermal fuse disconnected the two wires. Put new one in connected the wires. Then took out 1 screw that held the thermostat in place took 4 wires off. Put new one in reconnected the wires. Vacuumed out the back. Put back panel on. Connected the vent hose, plugged the dryer in. Pushed the start button & started drying clothes. Very easy!

It was really easy I watched your video on how to do it the video went step by step and was very helpful