Models > KESA907PSS00 > Instructions

KESA907PSS00 KitchenAid Range - Instructions

All installation instructions for KESA907PSS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KESA907PSS00
1-15 of 74
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Self Cleaning blows the thermostat fuse

  • Customer: Joseph from Worthington PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 69 of 74 people found this instruction helpful
Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.

First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.

This repair would have cost $164 through A&E factory service.

Radiant element, 2400 watt, under Ceran glass cok top needed replacement.

  • Customer: GEORGE from NEWNAN GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 54 of 114 people found this instruction helpful
turned off power
removed ceran top from cabinet
removed element
installed new element
replaced top
powered up and was done

Power shut down and door lock-up after self-cleaning

  • Customer: john from new market MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 24 of 26 people found this instruction helpful
My wife used the self cleaning function for the first time after 1.5 years of owning, of course out of warranty. A quick google search identified the problem. Called Kitchenaid, they said of course it can't be that simple, they had never heard of this problem, need to schedule a service call. Googled and found this site, Ordered the part, came in, only took a screwdriver and about 20 minutes, just like all the other posts.

shame on Kitchenaid for not owning up to the problem. I even e-mailed them all the links, they did not acknowledge them.

No heat on burner

  • Customer: paul from trumbull CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 18 of 24 people found this instruction helpful
Turned off electricity! Pulled stove out -lifted up glass top(carefully) simply removed burned out coil and replaced it with new one.

After using the self cleaning mode on this oven the oven would not heat, but the power remained on, only a heating problem.

  • Customer: Laurie from Camarillo CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 14 of 17 people found this instruction helpful
My husband did the repair and said it was very easy to do with the following instructions that I got from the Fix Ya website.

This is a design flaw in the Kitchenaid convection ovens. I can help fix this problem if you have a built in oven (I don't know if the parts are located in the same place for stand alone ovens). First it is not a FUSE that has blown rather it is the thermostat in the rear of the oven. (Part #4452223) This small part cost about $37 US and after shipping it will cost you about $47. I tried to get an estimate from an electrician as to what of frustration I decided to tackle the problem mthey would charge for the part and to come out and fix the oven an the price was about $90 for the part and anywhere between $100 and $170 more for the service call + repair! After a day myself.

The very first thing you must do is shut off the circuit breaker to the oven and put a very large sign on the panel that reads DO NOT TOUCH! That is 220 volts to that oven and while most panels have just the oven ont circuit you dont want anyone reactivating that circuit by mistake!

The next part requires a little work. Find the side panel screws (usually located in the oven door) and remove the two panel flanges that cover the 2 or 4 mounting screws that keep the oven in the wall. Now go underneath the oven and find the power junction box, take off the cover and disconnect the wires that run from the oven. Remember which goes where. Next remove the little nut that holds the electical conduit cable to the junction box then loosen the wires. Once this is done you can now slide the oven out and get to the thermostat.

This part requires a little elbow grease. Find a platform or table that fits just under where the stove will slide out and slide the oven on top of the table or whatever for support. In the back of the oven there will be a sheet metal panel that covers the thermostat and other wires, remove the 5 or 6 screws that hold this panel on and put the panel aside. Almost in the middle of the oven's back you will see a little black device with two wires running out of it (one red the other white or yellow). It will have the part number on its front, remove the wire and notice that the thermostat is half red and half white (remember this for the new part will have the same markings) the red wire goes onto the lead coming from the red markings. When you have the new part simply put the new one in (remember: the red side to the red wire), attach it to the back of the oven, replace the sheet metal cover and slide the oven back into place securing it with the screws. Viola! you are done! Turn on the power and then test the oven (I used the broil setting to warm it up then switch to a temperature setting). The entire process took me about an hour and I am NOT a handyman!

faulty meat probe

  • Customer: Kent from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 30 people found this instruction helpful
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

Bad Element

  • Customer: Michael from Howell MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 30 of 67 people found this instruction helpful
Bought new element and installed. Very simple. Used phillips
screw driver.

Original oven gasket had discolored and deteriated, mainly due to use of oven cleaner.

  • Customer: Ralph from Green Bay WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 12 of 15 people found this instruction helpful
I removed the bottom gasket retainer , single screw, with a screwdriver. The old gasket just pulls away. I cleaned the area under the old gasket with soap and water. I installed the new gasket whcih easily slips in place with the already installed retainer wires into the pre drilled holes.

Viola. Lokks like new.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 13 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Defective Surface Burner Element - 1800W

  • Customer: Robert from Daytona Beach FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 13 of 20 people found this instruction helpful
First discount Ac from wall, then take out 2 screws on the front of the range top and lift up the top of the range surface, then while holding up the surface top take out the front burner and replaced new burner element.Let the surface top down and screw in the two screws. the surface top of the range is hinged so it would be good to have someone to hold the top up while you replace the element or use a piece of wood to hold it up,this is a piece of cake to repair. would like to thank parts select for their service. I have ordered from them before and they back up their products
Robert

someone did not install cord properly! they left a strong strain on one of the 3 wires, with a loose nut connection that caused it to heat and melt the plastic that poped out toward the rear metal cover and short circuited.

  • Customer: Richard from Daytona Beach AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 14 people found this instruction helpful
I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

bought floor model with loose cord that melted block terminal

  • Customer: larry from alexandria IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 9 of 10 people found this instruction helpful
Safety first always shut breaker off at box.
I unplugged stove, disconnected wires keeping in mind the color placement. Unscrewed one ground screw and removed terminal block. Attached new block with ground screw, replaced wires in correct order, re-attached plug. Then reattached safety cover. Pretty simple for d.i.y.

al 4 interior lights had burned out

  • Customer: Kimberlee from Rocklin CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 14 people found this instruction helpful
The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

After using the self cleaning feature the oven would not work

  • Customer: Sherrill from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
Don't, Don't, Don't!!!!!!! call a repair man to replace the thermo fuse. If you are able to use the T.V. remote and crack a twist top off a cold beer, then you can DO this. I am 47 years old and half retarded and my 84 year old neighbor and I completed this task in 12 minutes. Turn off the breaker panel, pull the oven out, (it is hard wired). We placed it on a 4 wheeled dolly. Unscrew 11 screws, pop the panel. The fusee is at the top/center with two screws holding it. Pull the two wires off, screw it back in place. Put back the panel & 11 screws. Put the oven back in place. Turn on the breaker and you are done. PS Tell your wife or girl friend this might take an hour or so. Send her to the store for a six pack & steak.

Replaced our oven racks, becasue I (the husband) forgot to remove them before the "Self-Clean" process and they turned colors just as the instruction manual said they would !!

  • Customer: Kevin from Joliet IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 11 people found this instruction helpful
Easy, pulled out the old dis-colored racks and slid the new ones in. I was VERY happy with the quick receipt of my order. If I ever need parts again,this is where I will go
All Instructions for the KESA907PSS00
1-15 of 74