Models > KERA205PSS4

KERA205PSS4 KitchenAid Range - Overview

Get Parts and Repair Help for KERA205PSS4

If you know the range repair part you need, you can browse the list of all parts on the KERA205PSS4, or you can search by name or part description. You can also find your part by where it is located on the KERA205PSS4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for KERA205PSS4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 3 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 3 hrs and your part ships today!
$67.62

Sensor

This temperature sensor detects the temperature within the oven cavity.

Order within the next 3 hrs and your part ships today!
$39.84

Oven Rack

Sold individually.

Order within the next 3 hrs and your part ships today!
$14.71

Terminal Block

Order within the next 3 hrs and your part ships today!
$5.74

SCREW

Sold individually.

Order within the next 3 hrs and your part ships today!
$40.71

Infinite Switch - 8"

This switch controls the stove top surface burner.

Order within the next 3 hrs and your part ships today!
$5.05

Touch-Up Paint - White

18ml

Order within the next 3 hrs and your part ships today!
$22.93

Side Trim - Left Side - White

Screws are not included with the trim. Must order screws separately.

Order within the next 3 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The burner would keep heating after turning off the switch

  • Customer: RON from KAUFMAN TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 41 of 45 people found this instruction helpful
Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. ... read more

temperature not accurate after 3 1/2 years of happy usage

  • Customer: Ruth from Oregon IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 63 of 119 people found this instruction helpful
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I tur... read more

Replace shattered outer door glass

  • Customer: Philip from Vandalia MI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 29 of 36 people found this instruction helpful
This is not the best design. You'll need to have an extra set of hands to hold the trim pieces in place. Remember the glass is positioned outside [on top of]the trim pieces. Be careful as the trim pieces are rather brittle and can be hard to locate in their proper position. Position glass in the holding tabs at the bottom, hold glass against the trim piece... read more