KEHS01PMT2 KitchenAid Dryer - Instructions

removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

Removed back and found fuse bad, repalced fule.

At first I thought it was the ignitor, so I replaced it. No luck there. Next I went to the Part Select web site...that showed that the Thermal Fuse was the cause of this symptom 45% of the time. I installed the fuse and now my dryer is working!

open dyer door replace lint filter perfect fit, good price, fast delvery. thank you

downloaded video

Removed the old fuse and replaced with the new fuse. Of course, I had to remove the back of the dryer but very easy and the cost was less than $20.00. Definitely worth it because we did not have the money for a new dryer. PartSelect.com is awesome!

First I replaced the heating element. That did not fix the problem, so I used an ohm meter to test the thermostat and fuse (thermal cut-off). One of those was bad, so I ordered the thermostat/fuse conbo and put those in. The hardest part was getting the wires to the right places. I labeled them with masking tape and a sharpie, but maybe they are sized so they only fit one place. I didn't check. The actual work of changing out the parts was super easy. I recommend testing those three parts-heating element, thermostat, fuse-with an ohm meter before buying something you don't need. I now have a spare heating element and thermostat. I should be good for another ten years!

When the part came in my husband was not home and I figured I could put this part on myself. I took the part downstairs, used the nut driver to remove one screw, took the two wires off the old therma fuse, put the wires on the new therma fuse, and screwed the new therma fuse onto the back of the dryer. It really couldn't have been any easier.

took of the back , took out the drying coil ,put the other in , but back on . now it works saved alot of money. love it. Thank you parts select.

This has happened several times to my KitchenAid dryer. It cost more than $100 to bring someone in to repair. Fortunately, I saved my bills and saw the part "thermal fuse" listed. I researched that and found your website. I couldn't believe how easy it was to fix. The part cost less than $15 and the diagrams you provided were a big help. I was about to purchase a new dryer, easily $500. Your site saved me a bunch of money. How I fixed? Unscrewed the back panel of the dryer. Found a part that resembled the part you sent me. Slipped it out. Put the new one in...that is it. I also figured that one reason the part keeps burning out is because my duct has to bend to get to the outside vent. The obstruction probably causes the dryer to overheat more often than not. I pulled the dryer 6 inches more away from the wall to see if that helps. My fuse was going out about every 2 years.

Was working fine one load and not the next. I remembered we had used this site for our dishwasher so gave it a try. Went with most common problem first. Ordered Sun rec'd Tues. Took longer to vacuum the back of dryer then it did to replace the fuse. Cost less than 30 bucks including shipping. Video was cool too.

i still cant get it to start i keep having that 06 code revision after i ran the diagnostic i replace the thermistor right after that the dryer start but only dry one load and wont start again then i replace the thermal fuse still not working i order the door switch hopefully that might do it

Previous consumer help advised to check the Thermal Fuse. A quick check using an ohm meter or simply connecting the leads together, confirmed that the Fuse was open and bad. The other essential item is to clean & vacuum all lint from all other dryer parts on the top, drum & back of the dryer. Be sure to also perform a check of the Cycling Thermostat, located near the Thermo Fuse. This is not a difficult repair. Just be sure to disconnect the 220 V and the circuit breaker. A $9 fuse was better than the cost of a repairman or new dryer. Barry Burke, Cincinnati, Ohio.

My dryer is one of the energy efficient models (HE). The video for the installations was knowledgeable, but getting into the front of mine only required removing to screws from the bottom left & right corner (not using a putty knife to pop the springs). the plate on the front drops after that. Also when taking out the tube with the dryer element in it took a lot more twisting inside the frame to get it loose. Still turn it after the wire connections have been pulled off a little bit better than 1/4 of a turn. Also the heating element was in there really, really tight. It required tapping on the plate with a screw driver and a rubber hammer to take it out & put in (not that tough). After putting it in a 1/4 of a turn so that the tab was inside the blower tube. everything after that was pretty easy. The video showed this all being done in a clean dryer. It has been my experience that before all is running & closed back up that a vacuum or shop vac needs to go thru there to clean things up & prevent a future fire.