Models > KECM860TBC0

KECM860TBC0 KitchenAid Cooktop - Overview

Get Parts and Repair Help for KECM860TBC0

If you know the cooktop repair part you need, you can browse the list of all parts on the KECM860TBC0, or you can search by name or part description. You can also find your part by where it is located on the KECM860TBC0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. We’ve also included any installation videos we have for KECM860TBC0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.71

Drip Bowl - 6"

This part has been substituted by the manufacturer and has a hole in the center. It no longer has a solid bottom.

$9.80

Surface Burner Plug-In Block Kit

This newer-style terminal block kit includes two metal brackets, two pre-crimped wires with terminals, two ceramic wire nuts, a heat shrinking tube, and a mounting screw.

$31.28

Surface Burner - 8" - 2600W

***Please NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.

$28.56

Standard Y-Frame Surface Burner - 6" - 1500W

The manufacturer suggests replacing the receptacle at the same time.

$2.70

Screw

This screw is sold individually.

$23.61

Burner Switch Kit

This push-to-start Robertshaw style replacement for load rated switches has a clockwise rotation. It also has a break off shaft, and comes with plastic adapters.

$14.95

Thermostat/Selector Knob

This knob accepts a D-shaped shaft.

$8.44

USE MCN TJ114

$21.48

Grease Filter - Pack of 2

Only use these grease filters one at a time.

$2.70

Hex Nut

Part may differ in appearance, but functions same as original.

Common Symptoms of the KECM860TBC0 [Viewing 1 of 1289]

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

8 inch burner wouldn't come on. Wires shorted out

  • Customer: Jonathan from Lilburn GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 34 of 40 people found this instruction helpful
One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap. Cut the old wires ... read more

Burner would not heat

  • Customer: Edward from Malvern AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 23 people found this instruction helpful
First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the right level. I got ... read more

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce. read more