Models > KECC506RBL00 > Instructions

KECC506RBL00 KitchenAid Cooktop - Instructions

All installation instructions for KECC506RBL00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KECC506RBL00
1-11 of 11
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Hot Burner Light always on

  • Customer: Gregory from Cary NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 36 of 53 people found this instruction helpful
Thermal switch is integral to element and can not be changed, must replace entire element.

Turn off power. Removed front two screws above oven door jamb and lifted the top. Removed the bracket that holds the element against the glass top and removed the element. Moved brackets from old element to new one, aligning to same numerical position and then moved wiring to new element. Slide new element under bracket and reinstalled single screw. Replaced top and screwed down. Turn on power and test .

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 8 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

BURNER WOULD,NT HEAT UP.

  • Customer: david from cleveland TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVED TOP OF STOVE REPLACED HEATING ELEMENT ,PIECE OF CAKE.

Replaced the glass on our cooktop

  • Customer: Elizabeth J from Kerrville TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Called Appliances Plus, a local appliance repair shop; they came right our and completed the installation of the new glass in less than an hour. The toughest part was locating the correct circuit breaker as it was not in the breaker box we are used to using - repair person located it outside. Seems to be working just fine!

"Hot burner" Light always On

  • Customer: Stephanie from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It's easier with two people.
1 - Turn the breaker for the range to OFF
2 - Verify power is off by testing the burners and lights
3 - Remove front two screws above oven door jamb
4 - Lift the top and prop it up with the spoon, or have your helper hold it.
5 - Loosen the screw at the rear of the bracket that holds the elements against the glass top (front and rear are held by the same retainer)
6 - Remove the bad element by sliding it sideways from the retainer. Do not disconnect things yet.
7 - The burner has numbers around the edge. Move brackets from old element to new one, matching the numbers. Then move wiring to new element. New burner may have a single connector where old one had 2 and a jumper. If so, ignore jumper.
8 - Slide new element under bracket and reinstall the screw.
9 - Lower the range top and re-install the screws.
10 - Turn on power and test.

1200 watt r/rear burner element has an opening in the elementg

  • Customer: Jayson from Cape Coral FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

burner not as hot as it should be

  • Customer: Joel from Dillon SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.

Element stayed on high regardless of switch setting

  • Customer: James from Micanopy FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the part on line one morning and it was delivered the next morning. I was amazed at this because it said 3-5 days for delivery. I Opened up the range top and replaced the defective switch. This fixed the problem.

One of the burner wasn't light up.

  • Customer: Sam from Fairport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
All Instructions for the KECC506RBL00
1-11 of 11