Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KEBK171SWH00

KEBK171SWH00 KitchenAid Wall Oven - Overview

Get Parts and Repair Help for KEBK171SWH00

If you know the wall oven repair part you need, you can browse the list of all parts on the KEBK171SWH00, or you can search by name or part description. You can also find your part by where it is located on the KEBK171SWH00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for KEBK171SWH00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for KEBK171SWH00

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$25.98

Halogen Light Bulb - 5W 12V

This broil element, located at the roof of the oven, has push on terminals. The element supplies heat to the oven. If there is little to no heat when broiling and baking, or the element does not heat, replacing the broil element can be a solution. This part is around 12 inches wide and 19 inches long. To replace it, pull the oven door from hinges after removing screws. Next, remove the screws holding the elements in place and pull off wires attached to the back of the element. To finish off, add new element and screw it back in place. Remember to unplug the oven from the power source before beginning this installation.

$77.91

Element, Broil

This broil element is found on the roof of the oven.

$66.80

Temperature Sensor

The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty temperature sensor. A faulty temperature sensor can be a fire risk. If your sensor is not working properly, you should look to replace it straight away. A failed oven sensor is most often responsible for F3 or F4 error messages on electronically-controlled ovens. Make sure you disconnect the power to your range before you start your repair.

$46.50

Oven Rack

Sold individually.

$2.96

Screw

Sold individually.

$4.79

Screw

Sold individually.

$3.02

Screw (2)

This screw is sold individually.

$6.24

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$11.46

Spray Paint - 12 oz. - White

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave light-bulb went out

  • Customer: Eric from Camas, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 30 of 44 people found this instruction helpful
First, I removed the grill from the top of the microwave by removing 3 screws and then by sliding it out. It was a bit tricky, but you have to rotate it under so the grill comes out from behind the display.
Next, I removed the bottom grill by removing 4 screws. This one removed easily. Then, I removed 2 more screws that were under the bottom grill an... read more

Light bulb out in oven

  • Customer: Lee from Loveland, CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 43 people found this instruction helpful
Removed a screw and clip to remove the lens and replaced bulb. Then replaced clip and screw. Done. read more

Scratches in Surface

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 22 of 31 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. read more