This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined...
$84.88
In Stock
Order within the next 7 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Order within the next 7 hrs and your part ships today!
The temperature sensor measures the temperature inside the oven. If your oven is too hot, not heating evenly, is not heating enough when baking, or simply will not start, you could have a faulty tempe...
$89.97
In Stock
Order within the next 7 hrs and your part ships today!
This broil element is found on the roof of the oven. The broil element is at the top of the oven and supplies the heat to broiling. 14" x 15" with 1-3/8" inserts.
This part works with the following...
$191.89
In Stock
Order within the next 7 hrs and your part ships today!
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness...
$34.09
In Stock
Order within the next 7 hrs and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 7 hrs and your part ships today!
This is a replacement light bulb to illuminate the inside of your oven. It is 25 watts and 120 volts. Please wear gloves during replacement if your existing bulb is shattered. Consider ordering a spar...
$39.77
In Stock
Order within the next 7 hrs and your part ships today!
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Order within the next 7 hrs and your part ships today!
This authentic OEM black touch-up paint is specifically designed for repairing minor scratches, chips, or blemishes on your kitchen appliances. The bottle contains 16ml or 0.6oz of black paint and has...
$11.73
In Stock
Order within the next 7 hrs and your part ships today!
Questions And Answers for KEBK101SSS04
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
8 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Julie
October 17, 2022
Our oven is still working fine but is making lots of noise, particularly after use as it is cooling. The noise is sort of a squeaking, bird chirping sort of a noise.
It also seems to be hotter than before on the front/door of the oven. The oven is 11 years old but hoping it has a few more years of life.
For model number KEBK101SSS04
Hi Julie, thank you for asking the question. According to our research, the issue is probably with the fan blower, part number PS11745910. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Oven gets to temp then drops back down restart the oven and it shows temp and then the temperature drops again by 150 degrees have replaced element and fuse. Is it the control board?
For model number KEBK101SSS04
Hello Evan, thank you for the question. Based on our research, the issue could be caused by a faulty temperature sensor, part number PS11748765. It measures the temperature inside the oven. If replacing it does not help, we would recommend replacing the control board, part number PS11752581. Please reach out to customer service if you need help placing an order. Glad to be of help!
Oven gets to temp then drops back down restart the oven and it shows temp and then the temperature drops again by 150 degrees have replaced element and fuse. Is it the control board?
For model number KEBK101SSS04
Hi Evan, thank you for reaching out. You have checked almost every part related to this issue, we would recommend checking the following parts to fix the issue: the temperature sensor, part number PS11748765, the thermal fuse, part number PS11745932, and the control board, part number PS11748563. We hope this information helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
My broiler elerment is only recieving 120 watts to the outer element and 60 watts to the center element. The outer element glows red when on broil but the interior element doesnt. Is there a part that regulates wattage to the broiler element?
For model number KEBK101SSS04
Hi Mark, thank you for getting in touch. You will need to replace the broil element, part number PS11747304, to fix the issue. Glad to be of help!
Kitchen aide single wall oven bake element is not heating. The element has been replaced, and all connections and wires checked. It appears the element is not getting power. The broil element is functioning, and heats. Additionally, the thermal fuse was replaced very recently, it is functional. Suggestions to check next?
For model number KEBK101SSS04
Hello Rick, thank you for writing. This is likely due to a faulty oven control board, the Appliance Manager part number PS11748563 for your model wall oven. Good luck with your repair!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
This was easy and I'm glad I didn't go to the trouble and expense of hiring an appliance repair person. I'm reasonably handy, but I really have no experience in this kind of repair. I'd like to mention that the part I ordered arrived in just two days and it was exactly the right part, so I was very pleased in that regard.
Aft
... Read moreer turning off the circuit to the wall oven and confirming that the power was off, I had to remove the oven from the wall in order to access the wires and connections in the back. Normally, this wouldn't have been necessary because usually the broiler element can be disconnected from the clasps that connect it to the electric source by simply unscrewing the defective element from the roof of the oven, pulling gently on the connection ends from inside the oven cavity in order to "pull out" an inch or two of the electric source wires and the metal clasps that accept the "male" connecting ends of the broiler element. Once the a bit of the wire and the metal connecting clasps are exposed and able to be held with pliers, the element can be disconnected from the connector clasps by simply pulling on the prongs of the element (hard).
But in my case, one of the metal connecting clasp for one of the wires had melted, presumably when the element burned out, and that clasp could only be accessed and replaced from the back of the oven. Also, I would imagine that the wires and clasps could "slip" back behind the unit when they're disconnected if that's not done carefully. However, removing the wall oven was pretty easy for me -- even as a one-person job. I just put a tall table in front of it and slid it out so that it rested on the table.
If you have to replace a metal connector clasp, they're inexpensive and available in the electrical departments of hardware/home stores.
In my case, there's a metal panel at the back of the oven that had to be unscrewed and removed so that I could access the areas where the electrical source wires connect through the back wall of the oven to the broiler element. This was just a matter of removing a few screws and then removing the metal panel.
Once the metal panel at the back of the oven was removed, I was able to replace the melted connection clasp by using a wire cutter/stripper and then pliers to secure the clasp on the end of the exposed wired by deforming the clamp with the pliers. Once that was done, I simply removed the screws that held the broiler element to the top of the oven cavity, disconnected the remaining three clasps that connect the element to the source wires (the fourth clasp was the one that had melted and that I'd replaced), removed the defective element, inserted the four "male" prongs of the broiler into the four clasps that connect them to the source wires, replaced the metal panel at the back of the oven, screwed the new element back into the top of the oven, slid the oven back into the wall cavity, turned the circuit back on, crossed my fingers, and everything worked like a charm.
I saved a money, but more importantly (for me) I saved a lot of time that I would have had to have spent waiting around for a repair person.
