Models > KEBI271YBL2

KEBI271YBL2 KitchenAid Oven - Overview

Get Parts and Repair Help for KEBI271YBL2

If you know the oven repair part you need, you can browse the list of all parts on the KEBI271YBL2, or you can search by name or part description. You can also find your part by where it is located on the KEBI271YBL2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your oven. We’ve also included any installation videos we have for KEBI271YBL2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 12 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 12 hrs and your part ships today!
$28.25

Temperature Sensor

This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.

Order within the next 12 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 12 hrs and your part ships today!
$5.48

Light Gasket

Order within the next 12 hrs and your part ships today!
$18.07

2 Piece Broiler Pan

The top of this part is now black.

Order within the next 12 hrs and your part ships today!
$5.05

Touch-Up Paint - White

Order within the next 12 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 12 hrs and your part ships today!
$30.94

Light Socket

Order within the next 12 hrs and your part ships today!
$46.00

Bake Element

This bake element is found on the bottom of the oven. It has push-on terminal ends.

Order within the next 12 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 100 of 129 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Socket Light had a bad thread

  • Customer: Edmund from Emporium PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 21 of 28 people found this instruction helpful
Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover read more

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 16 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. read more