KEBC167VSS01 KitchenAid Wall Oven - Instructions

Turned off circuit breaker to oven
Removed oven door
Removed screws of reflector plate and top and back of oven
Gently pulled element out and down slightly
Removed slide crimps on wires
Replaced reflector plate on new element
Connected slide crimps on wires
Screwed reflector plate with new element to top and back of oven
Done. Total time 22 minutes
Tested and it’s perfect!

The oven is a KitchenAid convection oven with 4 panes of glass. The front, two inner glass panes that aren’t “touchable” and the interior glass that is the one that takes the heat from the oven and which you can clean easily - this is important because the descriptions of the glass all say “inner glass”. This is door #3 in the diagram that measure 10 x 22”. Which I cracked when I was pouring water into a pan to create steam for bread baking (lesson learned).

Because of the age of the oven, to remove the oven door it was necessary to place “pins” (we use medium screws) into the hole behind the door latches. Then were able to lift off the oven door. (We saw some videos on YouTube)

We placed the oven door on the counter top and removed ALL screws that held the door at the bottom and around the casing - KEEP these screws separate by where you’ve removed them so you replace them into the proper section when you reassemble the door. Each glass you remove has slots that hold them in their proper places. I recommend taking a picture BEFORE you take out each glass as there are brackets that need to go in proper order and you don’t want to forget the order.

We had to flip the door over in order to CAREFULLY remove the casing and access the different inner glass sections (took the opportunity to really clean them). Gathered the broken glass pieces into a paper bag and vacuumed the fragments. Then we were able to place the new interior glass from PartSelect, and reassemble the oven door. It’s perfect!

This took some time most likely because it’s a very old oven and you need to be methodical. I was just glad to be able to get the part - not yet ready to replace the oven.

BTW, originally I was guided to order glass #7 which is one of the inner glass panes that you cannot touch - unless you take apart the oven door - The exchange for the proper door was handled very quickly and easily. Hope this helps.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

Repair was really simple. Saw that the outer shielding on the existing heat element had degraded and ordered a new element. Part was shipped to my house in two days. Actually took me longer to get the oven door off than to replace the element because the left bracket on the door was slightly bent. Element came out after removing 4 screws and disconnecting 4 wire terminals. I was able to do the repair inside the oven and did not have to pull it away from the wall as the wires were long enough to pull through. I used some painter's tape to tape down the disconnected wires so they would not fall back behind the oven. Then I used a needle-nosed pliers to slightly crimp the wire terminal to the heat element and screwed in the four screws. That was it! Never did this type of repair before and it was really easy. Also estimate that for my 20-25 minutes of work I probably saved over $200 in parts and labor if I hired someone to do it.

good, used tie wire with a hooked end to fish one wire out of the back, to keep from removing the oven

I was stopped by the third screw on the roof of the oven, which was slightly rusted and would not budge in spite of using WD40! I had to enlist the aid of my son who arrived with better tools, including a SQUARE phillips head socket set. He also had to spend some time pinching and slightly reconfiguring one of the attachments in the back which did not slide together naturally. So, for an 82 year old retired housewife this was not as simple as it looked, but it was a piece of cake for guys like Erik with the know-how and the proper tools!

Turned the breaker off to the stove.
Removed 4 screws holding the element in place.
Disconnected the electric connection from element.
I had to replace the screws which were corroded.
Connect the new element electric connection.
Replace the 4 screws.
Turn on the power.
Turn on oven to burn off the smell of the new element.
You are done.

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.

Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

I removed the Oven door, unscrew 10 screws, open up the dor case, clean all glass levels, replace inner glass, reassembled the door, reinstalled the door to the appliance.

removed door, took out 8-9 screws, slid door upward, and removed. took out broken glass, and replaced.

First I removed the door from the double oven as instructed in the owner's manual. Then I removed the screws holding the door together. I removed the layers necessary to get to the inner door glass. Then reassemled it in the order that I had taken it apart. A total of 15 screws. My tip would be pay close attention to how you disassemble.
Not only did we save the cost of a repairman but because of Part Select we got the glass for less than half the price quoted to us from Kitchen Aid for the part and delivery.
Very satisfied with our experience with Parts Select