Models > KEBC167MSS03 > Instructions

KEBC167MSS03 KitchenAid Oven - Instructions

All installation instructions for KEBC167MSS03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KEBC167MSS03
1-15 of 106
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broke the glass panel inside the oven door -- dropped a baking dish on the glass!

  • Customer: Robert from Wildwood MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 79 of 104 people found this instruction helpful
Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!

No heat after cleaning oven

  • Customer: Frederick from St. Louis MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 52 of 58 people found this instruction helpful
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

Cracked the inner door glass by wiping with wet rag when hot

  • Customer: James from Renton WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 26 of 31 people found this instruction helpful
Removed the oven door by following the straightforward instructions in the user's manual. Removed philips head screws to take the door assembly apart. Removed clips holding the two inner door glass plates, and the two plates. Removed the clamp holding the broken glass plate, then the glass and associated glass fragments. Then cleaned and re-installed the three glass plates and their clamps in reverse order. Re-assembled the door and re-attached to the oven. Only cautionary note is to be careful when removing, handling and re-installing the various glass plates. Watch out for fragments from the broken plate; they can cut you and/or fall on the floor.

Replacing Top Oven Inner Glass Door

  • Customer: Melissa from Stockton CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 24 of 35 people found this instruction helpful
We had to remove two screws from the bottom of the outer glass door that held two brackets. Those brackets held the glass door in place. Then we had to remove two more layers of glass after that using a screwdriver. Then the inner glass, which was the one broken, we had to use pliers to bend the metal tabs that were holding it in place. We got the new glass in, bent the metal tabs back, returned the other two layers of glass, and then slide the outside glass door back in and returned the two brackets at the bottom. The hardest part was figuring out how to get started. Once we removed those bottom brackets, it was pretty easy after that.

Microwave light-bulb went out

  • Customer: Eric from Camas WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 21 of 29 people found this instruction helpful
First, I removed the grill from the top of the microwave by removing 3 screws and then by sliding it out. It was a bit tricky, but you have to rotate it under so the grill comes out from behind the display.
Next, I removed the bottom grill by removing 4 screws. This one removed easily. Then, I removed 2 more screws that were under the bottom grill and was able to start sliding out the microwave unit.
I was only able to pull the microwave half way out because some wires were stopping me from pulling it out more. I removed the big square piece of insulation and had enough room to get to the light assembly.
I removed the retaining clips by pushing the right side of the clips to the little opening in the middle on the right hand side. Then I was able to remove the light bulb and replace with the new one.

cracked iner door glass

  • Customer: william from albuquerque NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 17 of 21 people found this instruction helpful
Important note: hinges are left and right do not mix them up or door will not re-assemble properly and you'll get to do it twice.

Steps I took:

Removed the oven door per the instructions in the oven operator manual. Removed several screws to release the interior steel liner.

Removing the steel liner was a bit of a hassle, Had to manipulate it to get it loose but it eventually came away from the stainless steel exterior door panel.

Disassembled the interior glass layers, there are three. The glass you need to replace is the last layer, of course. removed and discarded the broken glass. Note: the interior glass is not secured by a bracket or screws, it is held in place by compression of the interior steel liner and a another liner that is inside the door assembly (you'll figure this out when you dis-assemble).

Another note: there is a fluffy material gasket between these two liners, use care when you disassemble or the fluffy gasket will turn into confetti.

Take the opportunity to clean all glass and parts of the accumulated oven grease.

Re-assembled door and re-installed...looks good.

Another note, getting the door back together requires a little patience because there are clamping overlaps of the steel liner to the SS exterior door panel. Be prepared to jockey things around a little and make sure all your screw holes are all lined up before you begin to button it up. Remember, hinges are left and right they are not interchangeable.

Oven wouldn't heat after cleaning cycle

  • Customer: Devin from Platte City MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 14 people found this instruction helpful
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

Light bulb out in oven

  • Customer: Lee from Loveland CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 33 people found this instruction helpful
Removed a screw and clip to remove the lens and replaced bulb. Then replaced clip and screw. Done.

faulty meat probe

  • Customer: Kent from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 18 of 30 people found this instruction helpful
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 14 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Broken Inner Door Glass

  • Customer: Ken from San Rafael CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 10 people found this instruction helpful
I removed the oven door by opening it to the horizontal position and inserting a small allen wrench in the open holes in each hinge. I then closed the door and lifted it free of the oven. I place the door face up on a packing blanket and removed the screws at the top of the door and the screws and clamps at the bottom of the door. I then lifted the outside glass door off the inner metal frame and set it in a safe place. I next removed the bracket holding the two inner pieces of glass and pulled the glass sheets out of the sheet metal holders. I then removed the screws which attached them to the metal door frame. Once the holders were off I removed the broken glass. I cleaned all the glass pieces and reversed the process to finish the repair.

inner glass broken

  • Customer: melody from Beltsville MD
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 12 of 16 people found this instruction helpful
Thanks to those who replied to my intitial distress call...because of them I had the courage to attempt the repair.
First I flipped the main electrica breaker.
then I removed the screws from the main door. The next step was to pop out the pins holding the hinges. I couldn't do that no mater how much WD-40 and lubricant I used, or how hard I tapped center mass.....SO I took all the OTHER components out staring with the side facings. (1 screw right left and 2 for bottom.)
Next I took the screws holding the door together out -- then the two screws holding the clamps on the bottom of the door. At this point I lifted off the the front facing of the door by the handle and placed it with its glass, to the side.

I then had access to the two inside panes of glass. They are secured with a metal plate screwed into the metal of the inner door. When I removed the two screws securing the plate, two plates dropped to the floor and it was fortunate I was holding the glas securly as it two would have dropped.
Next, I cleaned each of tpieces of glass with oven cleaner and set them carefuly to the side.(they were crusted with brown) Lastly I wiggled the broken glass out of the small inner window, working from both the inside and the outside of the window. Becuase I couldn't open out the door.. this was an extrememly time consuming activity..but do-able.

Once the inner glass was in screwed one of the screws o the clamp plate so I could rest the glass while screwing in the second screw. Once screw two was in place I took out the retaining screw and replaceed in with the glass clamped between. Aftern that the tough stuff was done and I just reassmebled all the door parts.

This SHOULD have been much simplier! IF I could have removed the hinge pins as directed.

Anyway, mission acomplished. Oven works fine.
Thanks!

Oven would not heat

  • Customer: Elvin from Richmond VA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

Inside glass of the oven cooled too fast and cracked

  • Customer: Grant from Anaheim CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
The repair is straight forward. The only complication anyone seems to be having is removing the door ( which is a definate must to do this repair properly). So I would like to add some details about removing the door. The manuel shows the allen wrenches going into what looks like the hinge itself to release it from the oven. This is not the case. The holes that the 5/32 allen wrenches go into are actually behind the hinge itself. I wrapped the allen wrenches with some painter tape to protect the surface of the door and oven from scratching. Then, simply insert the short end of the allen wrenches, one on each side, into the holes behind the hinge. Then as it shows in the manuel, gently close the door. But not all the way. As you get about 80% closed you'll feel resistence. That is the time to grasp the bottom of the door and start to lift it from the bottom, while stablizing it with the other hand holding the handle on the door. The hinge will start to release from the oven as you continue to press it closer to being all the way closed. The hinges will release if you are doing this correctly before the door can be all the way closed.

Hope that helps. Otherwise, once the door is off. Unscrew all the screws...pay special attention to what you are unscrewing and how it all fits together, because you're going to have to put it all back together again. Some of the glass is held in place with clips and some of it is not. Just lay it down flat and be careful to not force anything in or out and you'll find it quite easy.

Oven wouldn't heat after a cleaning cycle

  • Customer: Robert from Willow Park TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
Recieved the part promptly. From looking at the diagrams, we knew the overload thermostat was located on the back of the oven. We removed the screws, brackets, etc, slid the oven out, which for us was fairly easy as it's an under counter oven. Located the thermostat, removed it, replaced the new one, connected two clip wires, replaced the oven, turned the power back on and it works like a champ. Total cost was under 50 bucks.
All Instructions for the KEBC167MSS03
1-15 of 106