KEBC167MSS01 KitchenAid Wall Oven - Instructions

We had to remove two screws from the bottom of the outer glass door that held two brackets. Those brackets held the glass door in place. Then we had to remove two more layers of glass after that using a screwdriver. Then the inner glass, which was the one broken, we had to use pliers to bend the metal tabs that were holding it in place. We got the new glass in, bent the metal tabs back, returned the other two layers of glass, and then slide the outside glass door back in and returned the two brackets at the bottom. The hardest part was figuring out how to get started. Once we removed those bottom brackets, it was pretty easy after that.

Thanks to those who replied to my intitial distress call...because of them I had the courage to attempt the repair.
First I flipped the main electrica breaker.
then I removed the screws from the main door. The next step was to pop out the pins holding the hinges. I couldn't do that no mater how much WD-40 and lubricant I used, or how hard I tapped center mass.....SO I took all the OTHER components out staring with the side facings. (1 screw right left and 2 for bottom.)
Next I took the screws holding the door together out -- then the two screws holding the clamps on the bottom of the door. At this point I lifted off the the front facing of the door by the handle and placed it with its glass, to the side.

I then had access to the two inside panes of glass. They are secured with a metal plate screwed into the metal of the inner door. When I removed the two screws securing the plate, two plates dropped to the floor and it was fortunate I was holding the glas securly as it two would have dropped.
Next, I cleaned each of tpieces of glass with oven cleaner and set them carefuly to the side.(they were crusted with brown) Lastly I wiggled the broken glass out of the small inner window, working from both the inside and the outside of the window. Becuase I couldn't open out the door.. this was an extrememly time consuming activity..but do-able.

Once the inner glass was in screwed one of the screws o the clamp plate so I could rest the glass while screwing in the second screw. Once screw two was in place I took out the retaining screw and replaceed in with the glass clamped between. Aftern that the tough stuff was done and I just reassmebled all the door parts.

This SHOULD have been much simplier! IF I could have removed the hinge pins as directed.

Anyway, mission acomplished. Oven works fine.
Thanks!

Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

Used flat tip screw driver to pry front clip holding glass cover out of position. Pulled out dead bulb and pushed in new one. Slid clip back on glass cover and slid back into place. Simple. .

Kept removing screws and pulled things out until I got to the inner glass.
Yep, clueless and never did this before.
Put everything back in the opposite order of taking it out. Wala it's fixed.
Repair people wanted over $300 for parts and labor. However, with Partselect I was able to fix it for under $50.00 Well worth it!
Carmen

I followed instructions from the videos provided on the Part Select site. As with many such appliances, parts are interchangeable between brands. this unit is a KitchenAid but Whirpool,Kenmore parts interchange...Access from the front is all that's needed however and the only tool required was a phllips head screw driver...the only negative surprise (which the video warned about but I ignored) was the risk of the element leads drawing back through the holes, which 2 did. Save yourself that trouble by securing the wires to the back oven wall with a small strip of duct tape until you're ready to re-attach them to the new element. This necessitated removing the oven entirely for access to the back; the most time consuming aspect being removing/replacing what seemed like 20 odd screws holding the back cover in place! If not for that mistake, entire job would have been under 30 minutes. Well worth the effort and would do it again!

The inner glass on the wall oven shattered (apparently a common problem). Rather than look at a new $2-3,000 oven, I found the part for around $30. The repair was actually fairly easy, just had to be careful with the glass panes.
I did not remove the door completely, just worked on it either open or closed, depending on the step. First I loosened the two screws on the bottom of the door (when closed). Then I removed the four screws on the inside of the door and the two on the top part of the door (2). This allowed the outer panel to slide out and be removed.
Then there are two middle panes, held on by small clips with two screws in each. Remove one at a time, being careful not to drop any of the glass on the floor! Remember the order of the glass and the clips, so you can replace in the same order. (Now's a good time to clean all of the inner panes also, and to vacuum out the interior of the door.)
Lay these panes aside, and you should be to the broken inner pane, held on by a metal panel--again remove a couple screws, the panel, and remove all the broken glass. Be careful to retain all the insulation around the glass, and replace the glass, then the metal panel, the inner panes, and the outer door panel in that order. The outer panel should slide into place if you remove one clip and screw and start on one side, then replace the clip.

This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Getting at the part was difficult. The top and both side panels had to be removed to reach the blower. Once they were off, it was fairly easy to swap out the blower. The repair guy wanted $140 for the part and $160 to insall. I did it myself for $94! If you do it yourself, keep a good record of what screws came from where as you go. This makes re-assembly much easier.

Removed four trim pieces; removed four wood screws holding oven in cabinet housing; slid oven out (weighs about 150 lbs and takes two people and a bench to rest oven on. Oven will pull all the way out but not much further because of the electric cord.); Removed back sheet metal cover (bunch of small metal screws); removed wires from bad unit, unscrewed the bad unit and screwed in the replacement unit.

I have a rental and the tenant called. She said that she had a repair man out to fix the oven but he couldn't~that it needed to be replaced as he could not get parts.I contacted your company via phone and the person was so helpful~he asked the problem, looked up the model and advised me on this!It works like a brand new oven!Thanks you

There were 4 screws to remove and 2 wires to disconnect. We placed the order on line for replacement. It arrived the next day. We simply installed the new element by connecting the 2 wires (very easy) and putting the 4 screws back in place. It works like new and was sooo easy.

Our double-oven is wall-mounted, so accessing the backside to change the wires (as shown in the instruction video) was not a practical do-it-yourself option. After turning off the circuit breaker and disconnecting the broken broiler element, it is pretty easy to pull the four connection wires through the backside of the oven, which allowed us to disconnect the slide clips. We attached twist-ties to each clip/wire before disconnecting to keep the clips/wires from pulling back behind the oven wall when moving the new element into position. We found it necessary to crimp a few clips onto the new element to make secure connections, but the rest of the project went pretty much as shown in the video and the new element works great.

Removed back of oven. Disconnected 2 connectors on each side of element. Removed screws that were too rusted to use screwdriver with vise grips. Removed old element, inserted new element through holes in rear of oven.Installed 1 screw on each side of element in rear and 2 screws in front where brackets support the front of the element.Put back panel back on. Push oven back in place, plug back in outlet.It works great and I didn't have to pay service man.