Models > KDRU763VSS03 > Instructions

KDRU763VSS03 KitchenAid Range - Instructions

All installation instructions for KDRU763VSS03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KDRU763VSS03
1-15 of 22
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

faulty meat probe

  • Customer: Kent from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 25 people found this instruction helpful
Not a repair. Just needed to replace the meat probe sensor for the programmable oven. Quick and easy purchase and very fast delivery took care of the problem. I was back in business.

someone did not install cord properly! they left a strong strain on one of the 3 wires, with a loose nut connection that caused it to heat and melt the plastic that poped out toward the rear metal cover and short circuited.

  • Customer: Richard from Daytona Beach AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 14 people found this instruction helpful
I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

Burners kept clicking after ignited

  • Customer: Robert from Ranchos de Taos NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 9 people found this instruction helpful
This problem was driving me crazy for months. Of course, after I bought and installed the part and it still was not fixed I finally found a website that told me how to fix the clicking. The problem is that the removable head burners (#8 on the top assembly diagram) are not making good electrical contact with the base burners (#22). What I did was grab the head burners and grind them back and forth into the base burners with the weight on the heal of my hand. Steel wool or sandpaper would work too--you just want to clean the surfaces to restore electrical contact.
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one.

bought floor model with loose cord that melted block terminal

  • Customer: larry from alexandria IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 8 of 9 people found this instruction helpful
Safety first always shut breaker off at box.
I unplugged stove, disconnected wires keeping in mind the color placement. Unscrewed one ground screw and removed terminal block. Attached new block with ground screw, replaced wires in correct order, re-attached plug. Then reattached safety cover. Pretty simple for d.i.y.

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Burned Out Termincal Block

  • Customer: Jeffrey from Davie FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BTW - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 9 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

One burner would continually keep sparking after burner ignited

  • Customer: Michael from St Louis MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed the small access cover on the bottom of the cooktop by reaching inside and under the cabinets. Removed the module which was held by two hex head screws, unplugged the wires noting the location and color of the wires. Plugged the wires into the new module in the proper locations as noted previously. Attached the module with two screws, and then attached the cover/access plate with two screws. Problem resolved, repair was easy.

the spark igniters would continue to spark after the burners were lit

  • Customer: Robert from White Rock NM
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Since the problem would only occur when the right front burner was on, I first replaced the ignitor, but the problem persisted. To replace the spark module I had to pull the range out of the nook it is in in the counter top. Then (after ensuring that the power was off) I removed the back cover. The spark module was easily located and removing two screws and disconnecting a few wires liberated it. The new one went in easily since it is the same part number and an exact match. Put the back on and check that the problem was solved. Done!

would not light

  • Customer: ned from leland MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 5 people found this instruction helpful
remove two screws then unplug the wires put the wires back on the new one

broken meat probe

  • Customer: Daniel from Massey MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.

Terminal Block was melted where the cord had came lose.

  • Customer: Louise from Humansville MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.

The terminel bloc overheated and the bloc melted causing the stove to cease fukshioning

  • Customer: Joseph from Channelview TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
R&R

Wiring Block shorted due to moisture and Stove had no Power

  • Customer: John from Roberts MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.

The oven shipped without a temperature probe.

  • Customer: jerry from rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.
All Instructions for the KDRU763VSS03
1-15 of 22