KDDT207BAL1 KitchenAid Range - Instructions

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

I very simply replaced the gasket where it belonged and I was good to go!

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

easy enough, just remember the order if disassembly and reverse for instqllation

We looked at SEVERAL postings on this site. We ARE NOT DYIers. The descriptions on how to do this repair were super helpful. When we read that it only took 30-minutes and was easy, we thought, "Well, they haven't met us!" On the contrary, we got through this without one marital issue. It did take both of us and was kind of like a puzzle. It took us somewhere between 30-60 minutes. We left the door on and worked our way through screw by screw, panel by panel and "voila!" -- we were able to turn on the oven that night without it exploding!! Thank you Part Select and all of the DYIers that post on this site!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Just replaced them.

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

Remove the 3 Phillips screws along the bottom of the door, 2 screws on the inside and 2 screws on the top edge near the handle. Take off the outer door. Clean out the dust etc with a Vac. Tape the inner glass to the inside of the door so it doesn't slip loose later. Close the door. Remove the 4 screws under the foam to take off the middle window asm, not the 4 screws holding just the middle glass. Now when you remove this assembly the inner glass is not supported(this is why you taped it) so do not jar or lower the inner door yet. Now that the middle assembly is off support the inner glass with one hand and lower the door. Remove the tape and remove the glass. Now install the new glass being careful the gasket is in place. Reinstall everything in reverse.

Remove the door. This takes less than a minute. pull the door up and out. have a friend help you do this. Set it on a table and remove the outside panel screws and separate the outer face cover from the inner. this will expose the many glass window. the inner window has screws hidden under foam strips. these four screws must be removed to gain access to all other window panes. clean and replace as needed, then reassemble. Be carful not to drop the glass panels. also make sure that any insulation is reinstalled. Reinstall the door back into the spring loaded hinges. done

Had to screw off old terminal block & screw on new one