Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KBRS22KTSS01

KBRS22KTSS01 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KBRS22KTSS01

If you know the refrigerator repair part you need, you can browse the list of all parts on the KBRS22KTSS01, or you can search by name or part description. You can also find your part by where it is located on the KBRS22KTSS01 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KBRS22KTSS01 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$97.39

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$65.25

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$23.23

Light Switch

This part turns on the light when the door is opened.

$7.22

Touch-Up Paint - White

18ml

$29.83

Thermistor

Long harness thermistor kit.

$25.56

BLADE-FAN

The fan blade is used to blow air over the condenser.

$95.45

Icemaker Motor Kit

This kit includes the module motor, ejector arm, and ice stripper arm. The complete icemaker is sold separately.

$19.34

Drawer Gear Kit

These parts will attach to your drawer rail and are used to help the drawer glide smoothly.

$79.38

Freezer Door Gasket - White

This door gasket is used to make an air-tight seal for the cabinet when the door is closed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 661 of 696 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

No ice

  • Customer: Daniel from Suwanee, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 430 of 511 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 243 of 316 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more