Models > KBRS22ETWH00

KBRS22ETWH00 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KBRS22ETWH00

If you know the refrigerator repair part you need, you can browse the list of all parts on the KBRS22ETWH00, or you can search by name or part description. You can also find your part by where it is located on the KBRS22ETWH00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KBRS22ETWH00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$107.31

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$2.52

Light Bulb - 40W

Sold individually.

$3.76

Ladder Hook

Sold Individually.

$3.76

Water Filter Bypass Cap

$65.72

Dual Water Inlet Valve

The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold and to the water...

$65.93

Compressor Start Device and Capacitor

The capacitor helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed and the overload provides extra protection against excessive temperatures.

$14.89

Water Fill Cup and Bearing

$2.70

Screw

This screw is sold individually.

$4.46

Toe Grille Clip

$18.45

Light Switch

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 517 of 529 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 205 of 276 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

The refrigerator was not getting cold and the coils were not defrosting.

  • Customer: Cheryl K from Pinellas Park FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 73 of 80 people found this instruction helpful
Start by removing the freezer door and inner baskets so you have some space. Next, take out the ice maker by removing the 3 screws that attach it to the side and unplug it from the harness. Then the cover for the thermistor and the fan vent should be popped off carefully leaving the back cover only. The back cover is held on by 4 screws, one in each corne... read more