Models > KBRC36FMS00

KBRC36FMS00 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KBRC36FMS00

If you know the refrigerator repair part you need, you can browse the list of all parts on the KBRC36FMS00, or you can search by name or part description. You can also find your part by where it is located on the KBRC36FMS00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KBRC36FMS00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$44.50

Water Filter

This filter comes with cyst remover and fits refrigerators with a water filter located in the base grill below the door. It is recommended to replace the filter every 400 gallons or 6 months - whatever comes first.

$16.59

Water Filter Cap

This black water filter cap is located near the bottom kickplate.

$6.98

Light Rocker Switch

$14.89

Water Fill Cup and Bearing

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$67.84

Ice Mold

This ice cube mold and heater assembly has a flake resistant surface. It is used with modular style icemakers on some refrigerators.

$82.55

Icemaker Motor Kit

This kit includes the module motor, ejector arm, and ice stripper arm. The complete icemaker is sold separately.

$20.10

Fan Blade

Used with Evaporator Fan Motors.

$28.19

Thermostat with Clips

This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 327 of 391 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice Maker stopped working

  • Customer: Robert from Port Washington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 83 of 97 people found this instruction helpful
With socket wrench un-screwed the 3 screws and pulled out the ice maker assembly.

Pulled off white plastic end-cap and noticed the plastic gear disk had snapped off (sub part # R0167202)

However, it is all-one-part of the motor assembly unit # w10190935 (part # PS2341896) which must be ordered as a complete part.

Unscrewed t... read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 63 of 76 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more