Models > KBLA20ELSS00

KBLA20ELSS00 KitchenAid Refrigerator - Overview

Get Parts and Repair Help for KBLA20ELSS00

If you know the refrigerator repair part you need, you can browse the list of all parts on the KBLA20ELSS00, or you can search by name or part description. You can also find your part by where it is located on the KBLA20ELSS00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for KBLA20ELSS00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$70.13

Ice and Water Filter

This part has a high-quality carbon filter that reduces contaminants. Replace the filter annually or when the filter light is on. Sold individually.

$2.58

Light Bulb - 40W

Sold individually.

$66.61

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$20.29

Pantry End Cap - Left Side

Sold individually.

$50.79

Crisper Drawer

NOTE: As per the manufacture the crisper drawer has been updated from the original. A new crisper cover may need to be purchased for the drawers to work.

$29.24

Pantry Drawer Front

This part helps keep everything inside the drawer, it acts as a cover and also keeps you drawer at the proper temperature by creating a seal.

$18.55

Pantry End Cap - Right Side

This part mounts on the wall and is used to support the pantry drawer.

$36.81

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$7.68

Water Filter Bypass Cap

This cap is used when bypassing the filter.

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

light on to order water filter

  • Customer: Douglas from Byron NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 565 of 595 people found this instruction helpful
Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute. read more

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 380 of 452 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Removing the existing filter by rotating as directed and then dislodging from 'docking' station proved difficult. Turns out, the old filter is under a bit of vacuum pressure and getting the unit to separate or release was a challenge.

  • Customer: Jake from Novato CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 188 of 278 people found this instruction helpful
I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady... read more