KBFS25ETSS01 KitchenAid Refrigerator - Instructions

Removed ice maker.

Bottom freezer made access a tad awkward.

New unit did not come with wiring harness, or wire rod that activates cycle, or the front cover, which required transferring those items from old unit. Instructions on internet did not address this.

Installed new unit.

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

I pulled out the slide out drawer the shelf on top of it too a nutdriver and remove the broken panel while the daughter-in-law cleaned out the drawers. popped the new back in a srewed it back. It was so easy I could not believe it. I am 65 and a woman!!! I was done way before my daughter-in-law was finished cleaning. LOVED IT!!!!!!
Thank you so much for this wonder website. Barbara from lake worth,fl

Pulled out the meat tray drawer and crispers above and removed the sheet of glass between them. Removed the nuts holding the old pantry end cap and replaced with the new one. Replaced glass, crispers, and meat tray drawer. Very quick and easy. Delivery was unbelievably fast.

Thank you PartSelect. Ordered the replacement icemaker for our Amana refigerator, watched the installation video on PartSelect.com. Followed the instructions, took 15 minutes, works like new. Couldn't have been easier.

Side by side refrigerators are tough to get two arms inside the freezer side (and do much work) especially to unlatch the power connect. The water tube on this old refrigerator feeds from the back so I took a pair of kitchen shears and made a new opening in the back of the catch basin. Sealed the original opening. Don't know if that was necessary. The video was a big help for this parts change. Much easier than expected. G Keen

It took longer to take the items[food] out than to repair. It was very easy to replace.

Disconnted current icemaker and removed from freezer. Took off front cover and long arm that control ice dispenser. Put cover and control arm on new icemaker, reconnected bundled wires into new icemaker and clipped along side of icemaker and remounted into freezer. Connnected into back panel for power and checked water supply line to make sure it was lined up properly and job was done. Made sure arm was in down position, had ice cubes in an approx 90 mins.

First all product had to be removed in order to remove glass top that cover the crisper drawers, then removed both drawers and thenremoved the broken Crisper Frame Center Rail and installed the new part. Even with cleaning everything and putting it back together the whole job was only about twenty minutes of work time. Best thing of all was the price for the part, I will try to use PartSelect item for any other repairs I do on my appliancce!!

I found your website with the step by step video on how to replace the ice maker on my refrigerator. It looked really simple, so I ordered the part from you and it was here in 2 days. It absolutely took less than 15 min to remove the old ice maker and replace it with the new one----and it works. You helped me save close to $200.00. Thank you!!!

After reading one of the repair stories that applied to my same problem I knew exactly what to do from there. It was simple to remove the old one and install the new one. My ice maker is working great and no more overflowing water.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the electric plug.
Then I removed the old unit & replaced it with the new, reverseing the proceedure.

It's rather easy and straight foward
(I've done about 3 of them over the years)
take out the ice tray and if you can the top rack (depending on the model of your freezer) for more elbow room. unscrew the bottom screw under- neath the ice maker, then the two top ones, this makes it easier to remove the electrical connector.
take off the old plastic housing(snaps off) put it on new one, take the old wire harness off old, put on the new one, and last take the old wire that turns on the ice maker and shuts it off when full! that pulls out and snaps in the new one, and just reverse the install process!

Turned freez control off. unscrewed singl sheet metal screw, lift off unit, from 2 remain. screws, unplugged
elect connect. Pulled off sm water tube Rmd elect cable unit from old unit, installed on new unit.
Reinstalled elect connect, installed water tube,
Rehung unit on 2 sheet metal screws. Replaced the ice rail[with old one]Turned on freezr control. Had
cubes in 1hr, 4 min... Oh yes, took off old end
decor cover & slipped on new unit .. Greetings from
Hartland, Mi/USA

First I unplugged wiring harness from the inside of the freezer. Then removed two small bolts on top side and one on the bottom. Then took it out of the freezer. Then unplugged the wiring harness from the ice maker. Then plugged it into the new ice maker. Then reinstalled it back into the freezer with the three bolts.Then plugged it back in.