Models > KBFA25ERSS01 > Instructions

KBFA25ERSS01 KitchenAid Refrigerator - Instructions

All installation instructions for KBFA25ERSS01 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KBFA25ERSS01
706-720 of 768
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Chunks of non stick coating coming off. Water leaking into ice collection container.

  • Customer: Chris from jackson GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1.Pull refrigerator out from wall and unplug. 2.Turn the water source off! 3.Remove one screw from bottom and loosen two screws at the top of the ice maker. 4.Pull ice maker down and unplug the power connector. It has 2 locking tabs so press to release the lock. The water tube will pull out on it's own.5. Remove the cable, front cover and clips from old unit and install on the replacement unit.6.Re-Install new ice maker in reverse order. Always a good idea to take pictures before you do changes in case you are not sure.

Ice maker was leaking water.

  • Customer: Curtis from Rock Rapids IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screw from bracket on bottom side of unit then loosened the two screws on top side. Lifted unit off the two upper screws unpluged wires took cover off and removed ice arm, reinstalled all on new unit and installed it back in freezer. Did this in less than 10 mns.

Ice Maker Not Working

  • Customer: Corey from Bridgeton MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This process actually took 3 tries to resolve. Read the entire article it may save you money.
Before each trial I shut off the water and unplugged the refrigerator.
Trial 1
I went to the website and chose the part that had the highest percentage of resolution (78%), which was the actual icemaker. I followed the direction that another person described in detail how to replace. It was easy but it wasn’t the solution. It took me 15 minutes to switch out using a screwdriver and a nut-driver. Turned on the water and plugged the refrigerator in. However, after doing so I still had no ice.
Trial 2
Next, I tried replacing the small water pump that pumps water up to the ice maker. The part is called
the “Double Outlet Water Valve”. Here again on the premise that it was the next highest percentage part to fix my problem. I replaced this part in about 15 minutes with an adjustable wrench and a knife. This time a turned on the refrigerator and water squirted out of the plastic hose that feeds into ice maker’s water feed tube. Still no ice.
Trial 3
The last part to replace was the water feed tube which is a vinyl tube that extends from the outside back of the refrigerator to the ice maker. I read that if water shoots out of the plastic hose that attaches to the “Water Feed Tube” is most likely frozen. So, I replace the “Water Feed Tube”. I disconnected the plastic hose in the back and took some pliers and pulled the “Water Feed Tube” out from the back. It was frozen solid. I cut the new “Water Feed Tube” to the same length and inserted it into the back of the refrigerator. I will most like not go in all the way until you guide it in to the icemaker from inside the freezer. I used some good clear silicone caulk around the outside of the “Water Feed Tube” and attached the plastic hose to it with a small clamp. I was done in about 15 minutes. I plugged in the refrigerator and I let the caulk fully dry for 24 hours. Then I turned on the water. Within the hour I had ice. Finally!
What I determined was the “Water Feed Tube” froze up and caused the “Double Outlet Water Valve” to fail. So, it was necessary to replace both but not the ice maker. What happens in the process of making ice is as the ice maker cycles it calls for water from the “Double Outlet Water Valve”. You should first check to see if the “Water Feed Tube” is frozen. Remove it, use a hair dryer to thaw it out. Reinsert it and re-clamp it to the plastic hose. If that doesn’t resolve your problem or you find that it wasn’t filled with ice, make sure the “Double Outlet Water Valve” is pumping water to the ice maker. If it is, then, replace the ice maker. If it isn’t, replace the “Double Outlet Water Valve”. In other words, don’t go on the percentages. Go on the cheapest.

Bottom freezer was making constant grinding noises, then stopped making ice altogether. I researched the Amanda site, read the customer feedback info and instructions to replace the ice maker. We've been fortunate to have had no ice maker issues for this Amana unit for ten years! The fridge and fre

  • Customer: Sharon from Mukilteo WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled out the fridge, emptied the freezer, followed the video, which was very helpful. I watched it three times.

The ice maker that came with the refig stopped working after 1 YR!

  • Customer: Darwin from Sioux Falls SD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
If you watch the video on PartsSelect that will give you a general idea of how to do the repair except mine was in a bottom drawer freezer. You have streach a little to get to the screws holding the ice maker to un-screw them just enough to lift the ice maker out.

Not making ice

  • Customer: Dean from WYOMING MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
New part arrived in 15 hours with regular shipping. Watched your video and had old one out and new one in, in 20 min and ice in an hour more. Fantastic!!!

Original ice maker was leaking from a cracked tray

  • Customer: dean from holmdel NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
It is a simple and quick repair especially if one is even a little capable. May take some extra care and thinking for one who is not but still should be fairly quick and without troubles. I am not happy with the product as it does not make ice even half as quickly as the original. Many have stated the first or the first few cycles are very long and then it became quicker and more normal. Its been a week and I also tried shut it off several times just to reset it. It makes ice wonderfully but takes forever. I've yet to have a full bin of ice. Even without using ice for a couple days or very little in a few days. I am considering returning it for this reason.

inop ice maker

  • Customer: john from lakewood CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed ice rack and ice maker. installed and tested new unit.

Ice maker was dripping and creating a giant ice block

  • Customer: Sharon from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I never would have imagined that my husband and I could replace our ice maker so easily. We simply fired up the step-by-step video on my tablet, paused it as we did each step and voila! Usually there is a lot of cussing with any repair we do and I don't think there was even one cuss word uttered. Thank you for the clear and concise instructions!

follow the video that PartSelect has online

  • Customer: Rich from Wickenburg AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video and then do the repair.

Ice maker not making ice

  • Customer: JOHN from SAINT PETERS MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

The ice maker was leaking into the holding container and had black chips of paint or plastic from the inside of the icemaker

  • Customer: Gerald from Waukesha WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

ice maker quit making ice

  • Customer: denton from grinnell IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

Ice maker had been leaking for several months and needed replaced

  • Customer: Joe from Leonard TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.

The ice maker had been dripping and than stopped making ice. I worked with it and got it to work again for a few days and than the same problem occured.

  • Customer: Kathleen from Waller TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on line first. I shut off the power to the refreigerator. I took the one screw out on the bottom of the ice-maker and pushed up on the ice maker. Than I disconnected the power harness inside the refrigerator. I took it out and changed out the harness from the old one to the new one and also the bar that dumps the ice. I reconnectected the harness to the back of the refrigerator, made sure that the water spout lined up correctly. Pushed the ice maker down on the screws and reconnected the screw that I had removed. Waited about 1 hour and had ice cubes. This was an easy process after watching the video.
All Instructions for the KBFA25ERSS01
706-720 of 768