KBFA20ERBL01 KitchenAid Refrigerator - Instructions

turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

The repair was simple. It was a matter of unpluging the old relay and then pluging in the new one. I almost bought a new refrigerator but after doing alittle reading on this web sight and finding out the most common reason for having the problem I was having I decided to order the relay. It was the problem...$ 70.00 -v- $1400.00. I'm HAPPY !

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

We needed to replace both end caps for our Kitchen Aid refrigerator's pantry drawer. Although it seemed that after a few minutes studying your website's illustrations we knew what parts to order, still we doubted ourselves thinking it just seemed somehow too clear considering we were in unknown territory. When we received our parts we were careful to keep the boxes and paperwork together still believing there was no way we were going to be successful. Wrong ! We did indeed have everything we needed and our repair went really smoothly. It was truly a pleasure and so satisfying. Thanks for your illustrations, your how to video and your prompt delivery.

It literally took one minute. Snap off the outside of the old one and sap it back on the new one. Done!

The pivot block looked slightly worn because the hinge door mechanism on the left door would not "close" when the door was opened. I bought the pivot block, but the fix is adjusting the dual french doors so they are even i n height at the top of the unit. Pivot block is a 2 minute job with screwdriver. Adjusting the height is a 5 minute job with nut driver.

The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.

The drawer and drawer frame needed to be replaced. The part arrived on time, was correct and the repair was very easy.

I pulled out the old crisper and put in the new one.. For the other, I had watched the video so I saw that you needed a nutdriver to remove the cap. It was easy.

All you need to do for this repair is to remove one nut with a nutdriver. The part is removed by lifting upward. The wire assembly is disconnected. The new rail is installed by using the reverse order. That's it. Changing the pivot block is a no-brainer.

I have now replaced both the left and the right side Pantry End Cap. The Left side is extremely easy, but the right side is a bit tricky due to the drawer temperature adjustment lever. This is a mecanical adjuster that is made of plastic pieces that are linked together. Not super difficult but requires a little studying while taking it apart so you get it back together the same way. All in all a very simple job ,

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Removed crisper drawers, pantry lid, and rails. Removed pantry drawer. Unscrewed three bolts holding right end cap, and removed cap, taking care with temperature slide connection. Unscrewed (phillips head) drawer slide from end cap and removed temperature slide linkage and adjustment slide button. Installed linkage, slide button, and slide rail on new cap. Placed new cap in refrigerator, taking care to hook linkage into temperature slide. Reinstalled three bolts with nut driver. Reinstalled rails, pantry lid and crisper drawers.

We removed the old lid and snapped in the new lid. Done.