Models > KAWS777EQ0 > Instructions

KAWS777EQ0 KitchenAid Washer - Instructions

All installation instructions for KAWS777EQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KAWS777EQ0
1321-1335 of 1607
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cogs worn out, would not turn

  • Customer: Kent from Bakersfield CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Easy, popped cap off top of agitator with edge of knife. Removed bolt from center of agitator,pulled agitator up from shaft. Removed old,worn cogs,replaced with news cogs and reassembled. Tightend with bolt . Replaced cap and bang ,works like new.

not spining at full speed

  • Customer: mike from la porte city IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
this repair was really easy to do and did not take long. i used the video on whirlpool.com made it really easey. washer works like new.

Clutch dog teeth were warn causing the actuator to slip and not produce the required agitation.

  • Customer: Ralph from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the actuator cap which gives you access to the screw that holds the clutch dog assembly in place. Once the screw is removed the assembly lifts right out. The clutch dogs have a small retaining band that holde them in place. Once removed the dogs slip right out. Replace the old dogs and reverse the order of the removal process. Very easy.

Top half of agitator would not work

  • Customer: David from Austin AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
pull off softener dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

The agitator was not working in the washing machine.

  • Customer: BOBBI from SOUTH AMHERST OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I used the flat screwdriver to pop off the top of the agitator. then I used my socket wrench with extension to remove the bolt holding the top of the agitator to the bottom agitator. I pulled out the small piece that holds the agitator cogs. The agitator cogs were sheared off. I used my screwdriver to remove what was left of them, cleaned up the unit, then installed the new cogs. Re-insert the piece into the agitator unit and tighten the bolt back. Popped the lid back on top and ran a load of laundry to test. It works perfect! Although the teeth are pretty worn on the agitator as well, so I'm looking to buy a whole new agitator unit next. Very easy fix!!

top agitator was not rotating properly

  • Customer: Daniel from Hazelhurst WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
watched the repair video on u-tube and followed it. Had trouble separating the top agitator from the bottom agitator after removing it from the washer. I tapped the 4 white tabs on the top with a hammer and screwdriver. Top and bottom separated after that.

Agitator stopped turning

  • Customer: DANNY from LINCOLNTON NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
watching the video was a great help, not a perfect match as mine but enough information to get the job done! parts were cheap & they shipped fast. keep coming with the great videos!

Agitator would not work

  • Customer: Gregg from Mandeville LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Youtube video

Agitator not working

  • Customer: david from morehead city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
WENT RIGHT BY THE VIDEO, AND IT WORKED GREAT THANKS

agitator not working correctly

  • Customer: Matthew from Bellmore NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Parts came promptly. Disassemble agitator as per tutorial video on website. Replace locking "dogs" and reassemble. Cheap, effective fix!

Agitator and auger malfunctioning

  • Customer: Hilary from Plymouth MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Disassembled and removed agitator/auger unit by removing center cap, and removing center securing nut. Once on the workbench, further separated auger from agitator unit to access clutch, cam and four dogs. The old dogs had broken into two pieces each and no longer functioned. Upon obtaining replacement dogs, I simply installed them, reassembled the parts and remounted the center auger/agitator unit. Works like a dream.

washer shook even when empty

  • Customer: Bernerd from Messena NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
replased all the springs

Washer tub leans to one side. ( Not centered.)

  • Customer: Edgar Seabrooks from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

leaked water on the floor, out of balance in spin cycle

  • Customer: Edward from Falls PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
1)removed philips screws at sides of control panel 2)lifted up and flipped panel over backward 3) disconnected wiring harness to lid switch 4)removed two snap off connectors at top back of washer with screwdriver 5)remove top lid and side housing as one unit 6) removed removed top lid and side housing and core of washer to driveway 7) ran over unit with an Ingersol Rand 84" smooth drum vibrating roller

Water leaking from bottom of washer.

  • Customer: BRUCE from UNION NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We search on line the possible cause for our problem and Partselect offered the possible cause and solution. We watched the video on replacing the water pump.We then ordered the pump and 2 hoses.We followed the instructions and after removing the front panel, we found out one of the pump retainer was rusted away. We tried to look for local supplier and was shock that Sears was charging 20 bucks for a single retainer, which Partselect only charge dollar and eight cents. We ordered the 2 retainers on Thursday and it arrived on Saturday afternoon. We were able to fix the problem and are very happy there was no more leak. I wish the retainers come with the pump even if you include the extra cost to the pump pricing. We could have save the extra shipping charge for ordering the retainers only. I would definitely order more parts from Partselect and recommend it to my friends. Thanks again for your help.
All Instructions for the KAWS777EQ0
1321-1335 of 1607