KAWS750LQ4 KitchenAid Washer - Instructions

followed the tutorial from partselect--remove fabric softener dispenser(just pull up) remove bolt from agitator and take it off agitator--remove old parts and replace with new ones--reassemble---done.--- took longer to write this almost. Probably saved me 100 dollars. Almost anyone could do this repair if you can read and watch a video.

I generally followed the video. Disconnected the water hoses, removed the front, laid the washer on its back. My water pump is rusted onto the motor shaft so I left it in place. I removed the water pipes from the pump then removed the pump/motor/gearbox as one unit. Watch out for more water than you think being released from the pipes and pump!! Everything works well with the new clutch fitted.

Took the softener mechanism off by pulling upward. Pried off the cap to the agitator with a screw driver then removed the center bolt with a nut driver. This did take a little effort since it had never been removed. Pulled the agitator out of the washer and cleaned all the parts of any soap residue accumulated over the years. Took the agitator and stood it on the floor placing both feet on the sides and pulled it apart. there is a ring inside that popped out along with the top part of the agitator and the small cogs fell out. Cleaned the two pieces and replaced the cogs, holding the main part upside down lowered the agitator bottom into place matching the four grooves after snapping the unit together slide the cog cover into place and gently replaced the agitator back into the washer and replaced the bolt tightly. Then snapped the softener attachment back into place. This required a good bit of pressure but snapped right into place. Done job. Saved a lot of money and a simple fix to a problem. Agitator now works just as it should, no slippage at all. Took about 30 min all together. You can go online to find installation directions for any brand washer that has a full size agitator.

First let me say that I received the within 24 hours from when I ordered it online. Disconnected electric and water hoses .Removed screws on the top control panel then flipped it back from washer housing . Removed washer housing to expose main motor. Removed motor clips and screws . Removed motor coupling . Installed new coupling . Put it all back together . Works great!

Thurs. followed video directions, found the dogs to be defective and around 2 pm ordered dogs on line. To my surprise, on Friday around 11 am the dogs arrived. My husband installed them and the agitator is fine. I was so amazed at how quickly the dogs came. The machine was ready to go in less than a day. Thank you for your efficiency.

Follow the instuctions with the kit. Washer Machine Model # LSQ9244EQO.

I replaced lid switch. Take off two screws off the back of insterment panel. Unscrew switch and unplug. Then reverse. Easy!!

Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.

Removed cap from top of agitator, then used socket and extension to remove bolt which attaches agitator to shaft. There was soap residue accumulated on upper and lower agitator so I decided to remove that residue first. It took about 30 minutes to remove the soap residue with liquid detergent and a dishwashing sponge. Next replaced the agitator directional cogs per the video and installed the new washer on the bolt. After the lower agitator was back in place, the new thrust spacer was installed and lubricated with silicone grease, then the upper agitator assembly was re-installed per the vido. Put the cap back on the agitator and now the old Kenmore is running like new again. Before discarding your old washer, try to fix it. The new "energy saver" machines use as much water and run twice as long to do the same job. With the videos and troubleshooting aids provided by PartSelect you should find that most Whirlpool and Kenmore washers are not very hard to repair.

First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

The youtube explanation on how to repair was great, especially the instruction to lift up on the bluish plastic ring (to detach the softener dispenser), and not to tighten the bolt too much when reassembling matters.

removed the softener dispenser, gently pried off the top with screw driver, loosen nut and lift off the unit holding the cogs. On our (Kenmore, series 90) there was a small retaining ring to hold the cogs in place. Removed retaining ring (no tools), and cogs (one at a time). Replace each old cog with the new one, being careful that it's not upside down or backwards. reassemble. test. rejoice! This $3 part plus $7 S&H - saved a $100 house call from the appliance repair man.. YouTube & PartSelect = super Combo! Thanks!

Just like it said on YouTube. I am going to order a set of dog for back up.

I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.