Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KAWS750LQ3

KAWS750LQ3 KitchenAid Washer - Overview

Get Parts and Repair Help for KAWS750LQ3

If you know the washer repair part you need, you can browse the list of all parts on the KAWS750LQ3, or you can search by name or part description. You can also find your part by where it is located on the KAWS750LQ3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for KAWS750LQ3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.80

Agitator Directional Cogs

Agitator directional cogs, otherwise known as dog ears, come in a package of four and are generally found in washers where the motor is connected directly to the washer. The agitat...

Order within the next 7 hrs and your part ships today!
$11.77

Direct Drive Motor Coupling

The direct drive motor coupling, also known as a coupling kit, is a newer version of the part and is used in your washer. The piece includes new metal sleeves that have been added in order to strengthen the part. This part works between the transmission and the motor; it is only used on direct drive washers with no belt. In order to replace this part, you will need a flat blade screw driver, a quarter inch nut driver, and a Phillips screw driver. Before making this repair remember to disconnect the power supply, and both fill hoses.

Order within the next 7 hrs and your part ships today!
$21.32

Agitator Repair Kit

The agitator is designed to spin the clothes during a wash cycle. If your washing machine will not agitate, spin, or shakes and/or is noisy, you may need to purchase the agitator r...

Order within the next 7 hrs and your part ships today!
$2.92

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched out and lost its spring, it could cause the load to be off-balance which can cause excessive shaking, moving, noise and possibly leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screw driver, and a pair of needle nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually.

Order within the next 7 hrs and your part ships today!
$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpoo...

Order within the next 7 hrs and your part ships today!
$46.97

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to the machine not draining properly, leaving your clothes wet after a cycle. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate the need to replace your clutch. This clutch assembly comes with a brake cam driver, blue springs for large capacity washers, and a black spring for compact washers. As per the factory, the green spring (1.24 inches) replaces the black spring (1.46 inches). This repair requires a half inch 1/16th socket with an extension and a ratchet, a pair of channel lock pliers, a Phillips screwdriver, medium size flat blade, a small flat blade, and a 1/4 inch nut driver.

Order within the next 7 hrs and your part ships today!
$31.12

Water Inlet Valve with Mounting Bracket

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-color...

Order within the next 7 hrs and your part ships today!
$23.02

Switch, Lid

This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is having trouble starting, is not agitating, spinning, or is not draining properly, this could be because the lid switch has broken. You will need a 5/16-inch nut driver for this repair. The package will contain one lid switch. You will need to access the back of the washer, and remove the two Phillips screws that hold the top back panel in place. Slide the panel forward to release. Use your nut driver to loosen the screw that holds the ground wire in place. Lift the lid of the washer to release the old lid switch.

Order within the next 7 hrs and your part ships today!
$3.64

Thrust Spacer

This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in ...

Order within the next 7 hrs and your part ships today!
$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 925 of 982 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

Upper portion of agitator, no longer pushing clothing down.

  • Customer: Matt from Pawtucket, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 734 of 755 people found this instruction helpful
The instructions came with the repair kit, it was fairly simple and straight foward.

One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.

Ve... read more

washer wouldn't agitate

  • Customer: mike from Kent, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 686 of 715 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more