KAWS750LQ2 KitchenAid Washer - Instructions

First let me say that I received the within 24 hours from when I ordered it online. Disconnected electric and water hoses .Removed screws on the top control panel then flipped it back from washer housing . Removed washer housing to expose main motor. Removed motor clips and screws . Removed motor coupling . Installed new coupling . Put it all back together . Works great!

Thurs. followed video directions, found the dogs to be defective and around 2 pm ordered dogs on line. To my surprise, on Friday around 11 am the dogs arrived. My husband installed them and the agitator is fine. I was so amazed at how quickly the dogs came. The machine was ready to go in less than a day. Thank you for your efficiency.

Follow the instuctions with the kit. Washer Machine Model # LSQ9244EQO.

I replaced lid switch. Take off two screws off the back of insterment panel. Unscrew switch and unplug. Then reverse. Easy!!

Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.

Removed cap from top of agitator, then used socket and extension to remove bolt which attaches agitator to shaft. There was soap residue accumulated on upper and lower agitator so I decided to remove that residue first. It took about 30 minutes to remove the soap residue with liquid detergent and a dishwashing sponge. Next replaced the agitator directional cogs per the video and installed the new washer on the bolt. After the lower agitator was back in place, the new thrust spacer was installed and lubricated with silicone grease, then the upper agitator assembly was re-installed per the vido. Put the cap back on the agitator and now the old Kenmore is running like new again. Before discarding your old washer, try to fix it. The new "energy saver" machines use as much water and run twice as long to do the same job. With the videos and troubleshooting aids provided by PartSelect you should find that most Whirlpool and Kenmore washers are not very hard to repair.

First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

The youtube explanation on how to repair was great, especially the instruction to lift up on the bluish plastic ring (to detach the softener dispenser), and not to tighten the bolt too much when reassembling matters.

removed the softener dispenser, gently pried off the top with screw driver, loosen nut and lift off the unit holding the cogs. On our (Kenmore, series 90) there was a small retaining ring to hold the cogs in place. Removed retaining ring (no tools), and cogs (one at a time). Replace each old cog with the new one, being careful that it's not upside down or backwards. reassemble. test. rejoice! This $3 part plus $7 S&H - saved a $100 house call from the appliance repair man.. YouTube & PartSelect = super Combo! Thanks!

Just like it said on YouTube. I am going to order a set of dog for back up.

I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.

You fist unplug power and water and drain hoses. Remove agitator and lay machine on its back. Remove clips and water pump. You then remove clips and motor from tranny. Remove 3 bolts holding tranny and pull it and shaft from the machine exposing the brake assy. R&R assembly and reverse what you've done and you're done. machine worked like new. Always buy genuine parts they fit and work. Bob

The top agitator was not working. The top of the agitator should only work in one direction. Since it wasn't, the pawls (cogs) on the top agitator were worn. In order to repair, you need to take the top of the agitator off. Remove the fabric softener container from the top of the agitator. It should pull off. Then, remove the clear plastic cover. (clear plastic cover will have an 'o' ring on it.) Below the cover will be a 7/16" bolt holding the agitator to the washer shaft. Pull the entire agitator from the stainless steel shaft. You will need to separate the top of the agitator from the bottom of the agitator. It is necessary to separately order and replace the thrust spacer, grease, and bolt. All the other necessary parts are in the Agitator repair kit which is also necessary when ordering parts. The agitator repair kit will come with a diagram for assembly, otherwise reassembly is the opposite of disassembly. It took longer to write this installation instructions than it was to do the actual repairs.

Followed instructions supplied plus use of u-tube video. The job could have been done in less time if I had a long ratchet to begin with. Fairly easy job for a woman to do.