Models > KAWS750JQ0 > Instructions

KAWS750JQ0 KitchenAid Washer - Instructions

All installation instructions for KAWS750JQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KAWS750JQ0
1,606-1,620 of 1,692
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Out of balance, could't operate

  • Customer: Arlyn from Driggs ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.

Washer vibrated during the spin cycle

  • Customer: David from Roswell GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

when it would spin it would sheakall over .

  • Customer: Johnny from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just did it how the way it showed on the video it was easy

Tub was slamming side of tub during spin cycle and getting all out of balance

  • Customer: Steven Arthur from Tifton GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.

Washer shook in the SPIN cycle.

  • Customer: Mark from Dagsboro DE
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow the video to remove the cabinet. Did NOT have to lay the unit on its back in order to replace all 5 springs. These may be easily replaced with the washer standing upright. The back Suspension Spring was removed by using the access hole in the back of the washer to remove the screw holding the back spring bracket in place. Reassembled the cabinet per the video. Except for moving the washer around, this was an extremely easy repair. To facilitate moving the washer - use Moving PADS placed under the 4 feet of the washer.

Machine wobbled during spin cycle. Appeared to have some loosened part in the rear of the machine (noted some flexing on the front of the cabinet during spin).

  • Customer: Jonathan from Brandon VT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Disconnected electrical and then water inputs on the rear of the cabinet. Tipped the machine onto its front. Found that a spring was unhooked and dangling from a bracket. I searched for the location to secure the spring and found a hole on the rear base of the cabinet rusted through. I drilled another mounting hole nearby, Since the original spring had also broke, I replaced it with a new one from PartSelect, securing it between its bracket and the new retaining hole. Returned the machine to its upright position, reconnected water input lines, then its electrical. The machine works fine once again.

did not spin all the water out of clothes (clutch was slipping)

  • Customer: donald from alexander NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
followed repair instruction,( bought on line and down loaded ) some instructions were unclear but when you have the machine apart its obvious. your parts breakdown helped more than the instructions once the cabinet was opened.

drum wouldn't empty, washer stuck at that point in cycle

  • Customer: Steven from Chapel Hill NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Looked on line at Parts Select, and noted there was 66% chance that problem was in lid switch. Stuck screw driver in slot under lid, pushed on switch and made washer work, verifying that problem was likely in switch. Ordered part. Disconnected washer from electric/water. Removed screws on back and sides of panel; lifted lid and cover; replaced switch; reinstalled cover. Reconnected to elec/water. Worked. No problema.

Hanger on motor broke and destroyed the coupling

  • Customer: Andre from Torrance CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Turned machine on it’s back after removing the hose that goes to the drain, removed the bottom dust guard, I removed the hoses (take a picture before removing things so you know how to orient them when putting it back together) and drained the water first but this is not necessary (there are YouTube videos where they suggest removing the outer case, unclipping the pump and then removing the motor. This would be optimal as you don't need to deal with the water running out of the washer when you remove the hoses). Removed the 4 electrical connectors (multi-plug, 1 x two prong plug and 2 capacitor connector plugs) One of the motor hangers were broken on my machine, I removed the other one and then slipped the motor out. Removed the broken hanger and securing screws and the old rubber grommets, slipped the coupling out (had to leverage out with a large flat screwdriver). Installed new coupling and rubber on the gearbox side, 4 grommets on the motor and the other coupling on the motor. Inserted the hangers on the gearbox side and then mounted the motor. (it is easier if you turn the washer on its back so the drum moves down and gives you more room to drop the motor in from the top), clipped the motor hangers on and fastened the two metal screws, mounted the pump and hoses and reinstalled the dust guard. Turned it right side up and tested before dragging it back into the laundry. Washing again like it did when first bought it in 1998. I would recommend that when a coupling brakes, replace it as well as the hangers and grommets to make sure it has no room for play. Mine broke way too quick as I did the last coupling about a year ago, problem I think was that I had the wrong grommets causing excessive vibration and wear.

Out of balance on spin cycles

  • Customer: Darren from Saint Jacob IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the top part of the electronic panel. Removed the top lid. Removed the old tub springs and replaced them with new ones. Works great and for only $20.00. It beats buying a new washer. Thanks!

Cam in top of agitator was broken.

  • Customer: Richard from Palm Springs FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the fantastic video instructions and replaced the parts to make the repair. Very easy and all works well.

MACHINE WOULD NOT SPIN & REMOVE ALL WATER

  • Customer: ROBERT from CARROLL IA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed instruction found on line, they were very helpful and very well done by tech. I have a back ground in appliance repair mostly GE. I find the design of whirlpool washing machine was very well done, the repair of all major parts was easy and simple. Best designed washer I have ever worked on. Delivery of my needed parts was fast. I put parts in the machine it really didn't need, felt I could get another 10 years out of the appliance. VERY VERT SATISFIED, THANK YOU

agitator quit working

  • Customer: thomas a. from north port FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
job went great--thank you PartSelect for having the repair kit--getting fed up with all this high tech digal things--buy an older good washing machine and fix it yourself when it breaks--newer things have way to much electronics in them

Top of agitator not spinning or twisting with the base

  • Customer: Mark from Crestview FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Used the directions provided and used white lithium grease versus agitator grease working fine. You should really include the grease and include it in the package only concern.

Agitator was loose, weak and turning backwards .

  • Customer: Barbara from Sussex NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Just following instructions received from you people and, my wife Barbara ordered the parts, but her husband Joe made the repairs. By the way the machine is working very well now after 15 yars of use, thanks to you. Joe and Barbara
All Instructions for the KAWS750JQ0
1,606-1,620 of 1,692