Models > KAWS750GQ1 > Instructions

KAWS750GQ1 KitchenAid Washer - Instructions

All installation instructions for KAWS750GQ1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KAWS750GQ1
1,576-1,590 of 1,668
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Tub was spinning only part time. Had to have help getting started

  • Customer: Kingsley from Ewing IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

Bad Motor Coupler

  • Customer: Hilary from Gainesville FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
So, the instructional video was great but be warned that you REALLY need to hammer the part into place. Basically hammer it into place so that the end of the shaft that it goes on is flush with the plastic piece of the coupler on both ends. Otherwise, you'll put the washer together and run a load and it'll squeal and smell like burning rubber. We had to take it apart like 3 times before we got it on there securely enough. We would then run an empty load and it would be fine but as soon as we would add clothes the squealing and burning would ensure. So, my advice is to hammer it in well and save yourself the time and struggle!

Washer woulp not spin, brake cam driver not like video

  • Customer: Jody from Elk Creek CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
changed parts easily, following the video. Problem was the BRAKE CAM DRIVER, the plastic piece that fits around the shaft near the drum. The old one was visibly torn up, the pegs worn off, the whole thing worn down. The problem with the repair was the video showed an "E ring" holding it on and my washer had no E ring, had nothing hold it. It just sat there. Installed it anyway, although I was worried it was too loose. Sure enough there was a problem. it spun initially then started that ugly clicking noise. turned off washer immediately, disassembled again, and prayed. I found a large flat washer to take up the slack between the clutch and the plastic brake cam driver, reassembled, tightening the nuts a fair bit tighter than before. both the nuts on the transmission and the nut on top the agitator. works perfect!

direct drive motor coupling

  • Customer: Eugene from Chiefland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

Extremely wild rocking in spin cycle

  • Customer: Bryan from Midland NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

Washer vibrating when in spin cycle.

  • Customer: Calvin from Cheney WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced suspension, leveling and tub springs.

did not spin all the water out of clothes (clutch was slipping)

  • Customer: donald from alexander NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
followed repair instruction,( bought on line and down loaded ) some instructions were unclear but when you have the machine apart its obvious. your parts breakdown helped more than the instructions once the cabinet was opened.

drum wouldn't empty, washer stuck at that point in cycle

  • Customer: Steven from Chapel Hill NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Looked on line at Parts Select, and noted there was 66% chance that problem was in lid switch. Stuck screw driver in slot under lid, pushed on switch and made washer work, verifying that problem was likely in switch. Ordered part. Disconnected washer from electric/water. Removed screws on back and sides of panel; lifted lid and cover; replaced switch; reinstalled cover. Reconnected to elec/water. Worked. No problema.

Hanger on motor broke and destroyed the coupling

  • Customer: Andre from Torrance CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Turned machine on it’s back after removing the hose that goes to the drain, removed the bottom dust guard, I removed the hoses (take a picture before removing things so you know how to orient them when putting it back together) and drained the water first but this is not necessary (there are YouTube videos where they suggest removing the outer case, unclipping the pump and then removing the motor. This would be optimal as you don't need to deal with the water running out of the washer when you remove the hoses). Removed the 4 electrical connectors (multi-plug, 1 x two prong plug and 2 capacitor connector plugs) One of the motor hangers were broken on my machine, I removed the other one and then slipped the motor out. Removed the broken hanger and securing screws and the old rubber grommets, slipped the coupling out (had to leverage out with a large flat screwdriver). Installed new coupling and rubber on the gearbox side, 4 grommets on the motor and the other coupling on the motor. Inserted the hangers on the gearbox side and then mounted the motor. (it is easier if you turn the washer on its back so the drum moves down and gives you more room to drop the motor in from the top), clipped the motor hangers on and fastened the two metal screws, mounted the pump and hoses and reinstalled the dust guard. Turned it right side up and tested before dragging it back into the laundry. Washing again like it did when first bought it in 1998. I would recommend that when a coupling brakes, replace it as well as the hangers and grommets to make sure it has no room for play. Mine broke way too quick as I did the last coupling about a year ago, problem I think was that I had the wrong grommets causing excessive vibration and wear.

Out of balance on spin cycles

  • Customer: Darren from Saint Jacob IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the top part of the electronic panel. Removed the top lid. Removed the old tub springs and replaced them with new ones. Works great and for only $20.00. It beats buying a new washer. Thanks!

Drum moves and strange noise when spinning

  • Customer: Kenneth from Hillsborough NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
When I pulled the machine out, I noticed one of the suspension springs on the floor. I followed the video supplied by PartSelect.com and suggestions by other folks. I started with the spring that was missing, which was a mistake since I did not know that there are custom spring clips which hold the spring to the drum. Once I found the missing part the installation was very easy. I used the suggestion by another post, of wedging a block of wood between the back of the machine and drum, to relax the rear suspension spring, which eliminated having to remove the back of the machine or tipping the machine on the back to get at the screw. I will always look to PartSelect.com for any future appliance repairs. You are the greatest

Out of balance, could't operate

  • Customer: Arlyn from Driggs ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.

Washer vibrated during the spin cycle

  • Customer: David from Roswell GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

when it would spin it would sheakall over .

  • Customer: Johnny from Las Cruces NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just did it how the way it showed on the video it was easy

Tub was slamming side of tub during spin cycle and getting all out of balance

  • Customer: Steven Arthur from Tifton GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the cabinet apart really easily with Part Selects helpful video. Removed old suspension springs by removing outer brackets on two of them and by using pliers on the third one. The tub spring was totally missing. Put on two new brackets and springs with the nut driver. Then stretched the third spring into place. Replaced the tub spring by stretching into place and then put cabinet back together. All done very quickly!!! Now it works perfectly and runs very quietly.
All Instructions for the KAWS750GQ1
1,576-1,590 of 1,668