Models > JW3000A > Instructions

JW3000A Jenn-Air Washer - Instructions

All installation instructions for JW3000A parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JW3000A
256-270 of 284
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Had a difficult time getting the last washer on the transmission pully

  • Customer: Vickie from Harrison MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the video

clothes still fairly wet after spin cycle

  • Customer: jim from radcliff KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
tilted washer about 45 degrees off with old on with new belt.TOO easy

Washer would not spin

  • Customer: Steve from Polo MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After inspecting the brake and installing the new pulley/bearing kit the washer still would only spin slowly. Discovered that if the washer agitates at all in the spin cycle then the transmission is shot. So washer was replaced with a new one.

tub making noise during wash cycle

  • Customer: kevin from lees summit MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Watch the videos on it about replacing the snubber ring. Do not remove the whole assembly just loosen enough to get old snubber out and new one in, or you will find it very difficult to get the brake/clutch assembly back together Also I used a 2 x 4 scrap to push and hold the the barrel while removing the six springs. Wear long sleeves as the metal on the washing machine panels will cut you very easily. Belt was just sliding it over the pulley. One other recommendation is take a pictures before and while you are taking it apart for verification of reassembly.

transmission bearing melted ..

  • Customer: Louis from Dozier AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
put a total new transmission total kit on.

Hole in hose from wear & tear

  • Customer: Richard from Las Cruces NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened back panel. With pliers, moved the retainer clamps. Used a flat screwdriver to pry off hose from tank. procceded to remove hose from pump. Put new hose on and replaced hose clamps. Tested with a small wash cycle, no leaks. Job done.

The E clip (or C clip) is not easy to install!

  • Customer: TRUONG from LAKEWOOD CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was struggling for more than an hour trying to put the E clip on with the thicker washer as recommended then gave it up. I tried again with the thinner washer and still can not get the clip fully seated in place (only one end got into the groove). Frustrated, I decided to tap the other end with flat screw driver and hammer. The clip seems to be deformed but rested in the groove. Checked the brake adjustment and it was on the min mark. I did not dare to remove it for adjustment, and there is no thinner washer to adjust anyway. The washer is still working OK now after 3 loads. Other than that I am really happy with the purchase. Supper fast shipping. Very helpful instruction video. Only I am not really a handy man as my wife often encourages!

Noisy when opperating

  • Customer: Gerard from Chandler AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Turned washer on it's side with the backside facing up. Pump had part of the pulley missing. The belt was replaced as a precaustion. I didn't disconect any of the water lines, just un plugged. Note I was amazed at how quick I received the parts. I expected to wait a week and received parts in 3 days. Execelent service.

washer was making a loud whirling noise on spinout

  • Customer: Brad from Logansport IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
everything pretty much just unbolted real easy. the parts come with a nice set of instructions. you don't need to use the special hub removal tool. just take a small piece of wood and smack it on the ear of the hub to the left counter clockwise. it might be tough but just keep smacking it till it comes loose. then install it in reverse. simple job. you also might need some big vise scrips to get ahold of the springs real good to get them off and back on...

The washer making a ticking sound while in the washing and spinning mode.

  • Customer: Rudy from Yukon OK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I found the instructions on www.ehow.com about how to remove the shell of the washer so I could find what was going on with the washer and why it would smell like burning metal. I found it was the Drain Pump with Pulley Assembly P/N: PS2347187. It was easy to replace and saved $$$$ from having to purchase a new washer or call a repairman or women.

wASHER WOULD NOT AGITATE.

  • Customer: Ernest from Pasadena CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
pURSUANT TO THE VIDEO PROVIDED BY PARTSELECT, I DISCONNECTED POWER CORD, HOT AND COLD WATER HOSES. ALSO, REMOVED DRAIN HOSE FROM DRAIN PIPE CONNECTION. LAY THE WASHER ON ITS SIDE REMOVED THE PULLEY BELT THEN FOLLOWED THE VIDEO TO REMOVE DUST COVER, C-CLIP, CAM, PULLEY, THRUST BEARING ALONG WITH ASSOCIATED WASHERS FROM THE TRANSMISSION SHAFT.INSTALLATION WAS THE REVERSE AS SHOWN IN THE INSTRUCKIONS PROVIDED IN THE KIT.

machine moved and shook when in spin

  • Customer: virginia from central city KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
we followed the video instruction that was given,on how too replace the part of the snugger. it worked really well. we are pleased with everything.

washer shook uncontrollably during spin cycle

  • Customer: Adam from Plainfield IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video but didn't remove the motor. Instead I lifted the tub through the top. I also didn't have longer screws with that thread, so I used slightly smaller diameter screws with nuts on the end and it worked great.

pump and belt

  • Customer: tommy from thomaston GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
tilted washer up rolled belt off next removed panel in back of dryer next took hoses off next 3 screws on pump frame remove replace pump reverse steps easy also video on this site

a new belt

  • Customer: howard from crownpoint IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
unplugged mach laid over on side with quilt underneath, to keep mach from getting scratched,turned the pulley ,with pressure on belt slid off then put new belt on,piece of cake, I did watch your film on the belt removal.procedure ,thank you so much, and the belt was shipped to me el pronto,,it purrs like a new one thank you again ,im sorry I didn't know part no.
All Instructions for the JW3000A
256-270 of 284