JW1000W Jenn-Air Washer - Instructions

Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!

First I tipped the washing machine onto its front. I removed the belt on the bottom of the machine. Then I removed the screws that held the cover in place on the back of the machine. Next I removed the two hoses that were connected to the vertical pump using pliers to pinch the clamps. I then removed three screws that held the vertical pump in place. I took the new verticle pump with pulley and mounted it to the washer and putting the washer machine back together using the previous steps in reverse order.

Removed front cabinet, removed 6 springs holding tub down, removed pump hose, removed drive belt from motor,lifted tub out the top and placed upside down, loosened all six hex bolts(did not loosen or remove drive pulley) backed all six bolts out and left 4 threads showing, slipped old snubber out cleaned all surfaces with alchohol and slid new snubber in. Put corn starch on base where snubber rides, lifted tub back in, hooked up all six tension springs with auto brake tool. Put belt back on. . . Done. . No more beating itself to death.

Hardest part was removing front panel to access the motor.
Removed front panel, Tilted washer with block under the front. Removed belt. Used pully puller to remove damaged pully. Tapped on new pully with 1/2 in socket until shoulder seated on motor shaft. Replaced belt and front panel. Runs as smooth as new now. Additional note: I removed the plastic guard over the top of the motor and held an additional socket on the top of the motor shaft to avoid internal damage to the motor while tapping the new pully on the lower shaft.

Removed excess water,removed hoses,tiped back washer,removed belt,removed pulley and bearing. Removed 3 screws and replaced with 3 longer screws in the stator,then removed 3 shorter screws. Then loosen very slowly each of longer screws to relieve pressure from the brake spring. Once loose,pulled out brake rotor. Replaced with new parts. Works like new.

The drain pump assembly was going bad. It eventually froze and burned the drive belt and motor pulley up. I replaced the drain pump by removing 3 screws. I replace the motor pulley and belt in about 5 minutes without removing any parts. Simple fix. Ran through 3 cycles and works perfectly. Thanks!

I felt extremely confident when purchasing the part because I say three diagrams which clearly showed I was ordering the correct part. 0. Drain all of the water out of the machine. 1. Remove the rear panel from the washer. 2. Use the pliers to disconnect the hoses from the pump. 3. Remove the three screwa from the old pump. 4. Support the washer with the block then take the belt off pulley. 5. Remove old pump. 6. put new pump in place then reconnect the pulley, you can remove the block.. 7. Install the three screws for the pump after you tighten it up by placing the pump over ther correct screw holes.. 8. Reconnect the two hoses using the clamps you removed. 9. Secure the rear panel and screw in place. 10. Wash clothes. EASY FIX!!!

The hardest part of this is the springs. The best way to disconnect and reconnect was to tilt the tub towards the spring I was trying to work on (thus putting less tension on the spring and cutting down the distance). I took a large boot and jammed it into the oposite side wall to hold it in a tilted position before I disconnected the spring and then redid that to reconnect using a vice grip wrench. I replaced all three things, snubber, brake roto and stator and it went back together very easily. The key on the pully shaft was hard to reattach but there was a trick to that as well. The shaft has to move up slightly to slide ring on so you need to have something under the tub to help raise it. After that was back together it was 15 mins. to finish and now the washer is running like new.

This is a very simple repair, I opened the top of the washer by inserting a screwdriver between the top and the washer cabinet. There are 2 clips on the front of washer, locate and push in to release top. Lift top with lid attached and remove the 2 screws holding the lid to the top of washer. Remove lid and replace hinge pin and hinge.
Replace lid, close top , all done. Total time about 15 minutes or so. Now the lid will stay up and not fall on someone.

I first leaned the washer up and "walked" the belt off of the motor pulley. Then I lifted the top cover of the washer and propped it up so I had access to the screws in the front cover. I took out the two screws at the top of that cover and lifted it out of the way to get to the motor. I took out the mounting bolts and then removed the ground wires. I followed the lead of a previous "repair story" by taking the electrical wires off the old motor, one by one, and immediately putting them on the new motor in order to get them in the right spot. The only issue I had was that one of the ground-wire screws was smaller than the hole that had been tapped on the new motor. Otherwise it was really simple and the job was finished by completing reassembly in reverse order of disassembly. And the old washer seems to have more life in it today.

first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!

Removed the front panel, Removed the belt from pump in the back of machine. Removed the pump from the back of machine, Put the pump in reconnected the belt, Replaced all the screws. My husband did the repair work in a matter of 45 minutes. Machine works fine now. The part came when I was told it would. I am very pleased with your service.

Removed knob from timer and pulled off the plastic indicater.
Removed 3 screws from the top back of the controls panel and then two screws from the bottom front.
Removed controls panel.
Removed four screws from the controls mounting bracket.
Removed mounting bracket.
Removed two srews holding the timer to the mounting bracket.
Unpluged wire harness from the timer.
Installed new timer.
Put back together and done.

First push inner tub to left rear, all the way, and
unscrew hinge from inside of tub. repeat same on
right side. lift cover off and unscrew other half of
hinge off cover, both sides.reverse procedures and your done.
Note: always replace both hinge's new while
you have it apart.

The reason for the belt not turning was because of a cover in the water pump pulley which did not allow the water pump to rotate and that's why the belt and the plastic motor pulley burn out. First I removed that cover and then removed the belt, the pulley was easy simply by breaking all the little teeth with a screwdriver then the pulley can be remove by using a screwdriver as a lever. putting the pulley, simply use a plastic hammer so it does not get damage be patient. finally the belt and you are done, hopefully this will help someone.