Quick Question!

Have you ever purchased from PartSelect.com before?

Models > JVM2070SK02 > Instructions

JVM2070SK02 General Electric Microwave - Instructions

All installation instructions for JVM2070SK02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the JVM2070SK02
16-30 of 160
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I diagnosed the problem incorrectly: based on a previous repair.

  • Customer: Ralph from Brandon, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 47 of 105 people found this instruction helpful
The old fuse is perfectly good. The new ones arrived within a day.

Everything worked on the microwave, except it would not heat anything.

  • Customer: Randy from Ottawa, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 19 of 24 people found this instruction helpful
The microwave had been working fine until one day when the timer counted down but the heating motor (or whatever you call it) would not come on. So the timer would count down but nothing inside would get hot. I did not know what it was for sure but decided to take it apart and look. Once I had the control panal off, I found three small wired switches inside. One of these switches appeared to have shorted out. So I searched online and found Partselect.com. I found a matching switch , ordered it (arrived in couple days), put it in, and VOILA it works! Thanks Partselect.com.

tray broke

  • Customer: martin from the villages, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 20 of 28 people found this instruction helpful
replace tray

buttons stopped working

  • Customer: Shaughn from Washington, DC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 20 of 29 people found this instruction helpful
Remove filter holder from bottom. Then remove fan cover from top. Then swing open panel on right side of m-wave. You can then lift control assembly to remove it and access buttom assembly

Noise and no Heat on Microwave oven.

  • Customer: Luis from Plano, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 22 of 35 people found this instruction helpful
First, I waste $65 by calling some "REPAIR" service. They showed at home and charge me that just to tell me
Second, I researched on the web and ordered a part, which was not the issue. I waste abnother $72
Third, I found Part-Select and got the right answer: the Diode was the problem. Ordered the part form Part-Select and it FIxed it !!!

Note: I did not buy a new microwave because this one is mounted on the wall and it will cost me +$800 just the lowest price.

key module stopped working

  • Customer: Richard from High Point, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 24 people found this instruction helpful
Insructions said to remove filter frame from bottom and fan cover from top,but upon looking at fan cover I could see there was only one screw above the control panel on the right. I removed the fan cover and the one screw and had easy access to detach the control panel and change the key card. Dick Rowley

Grille holding venting mechanism broke

  • Customer: Kyle from Castro Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 16 people found this instruction helpful
First, I removed the two phillips screws on the top of the microwave. Then I was able to take the venting mechanism off of the microwave. I unscrewed all of the parts attached to the broken plastic vent and reattached them to the new plastic vent. Once all the parts were on, I simply put the venting mechanism back onto the microwave and placed the two phillips screws back to hold it in place. Lastly, I reattached the springs that allow the vent to close. A simple job done in less than 15 minutes.

Grinding Noise In Motor

  • Customer: MARK from VALLEJO, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 22 people found this instruction helpful
Removed upper cover. Removed screws in cover plate & motor mount. Removed inner cover with pop screw inside microwave. Reversed procees to install new motor.

No heat in the microwave

  • Customer: Douglas from Mechanicsburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 22 people found this instruction helpful
We purchased our Microhood oven about 4 years ago along with the extended warranty package offered thru home depot. Within one year, the problems began. Each year the secondary switch would go bad rendering the microwave useless. If you have 3 small children like we do, you tend to use it a lot. We sure take the microwave for granted.

Each time G.E. would fix the problem at no charge. Ths time - the warranty had expired and GE wanted to charge us $80.00 for service call plus parts and labor. We estimated the cost to run at least $150.00 or more.

To top it all off, GE was going to have a service tech avail for over 2 weeks. This is poor customer service and completely unaccceptable.

Because this was a recurring problem, I figured it was the same part that had being going bad since we purchased the appliance. I decided to order the part "secondary switch" myself and attempt to fix the microwave on my own.

I ordered the part last Tuesday, the part arrived last Friday. Within 10 minutes I had the microwave apart, replaced the part and had the microwave back in working order.

PartSelect saved me over $100.00.

We are very satified with PartsSelect, I would recommend them to anyone

Filter needed replaced

  • Customer: todd from greensburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 18 people found this instruction helpful
Remove two screws,slide panel to left and remove,install filter.Replace panel,and done.Service call would have cost $97,98. EH? No brainer!

No power to microwave

  • Customer: James from Highland, UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 21 people found this instruction helpful
Had trouble isolating the problem, so I had a repairman identify the problem, then I ordered the part and replaced it myself.

Removed screws holding the grill in place. Removed air filter, removed screw holding plate under the filter in place. Reached in under fan cowling to find the thermostat cut-out. Disconnected the two wires. Put the new thermostat in place. Replaced screws plates and filter in reverse order.

Broken glass turn table

  • Customer: Marshall from Sacramento, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 16 people found this instruction helpful
Open the box.. unwraped excessive bubble wrap.. placed in microwave.. Did'nt even break a sweat..

Loud noise from inside microwave

  • Customer: Allan from Huntley, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 14 of 23 people found this instruction helpful
I initally thought the problem was the turn table motor but after installing that motor & not being successful I realized the problem was the stirrer motor.Removing & insalling that motor was a bit more challenging but worth the effort as I saved either the cost of a repair technician or the puchase of a new one.The microwave is back in service & running fine.

Broken light lens for the light bulbs

  • Customer: TERRELL from OAK POINT, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 15 people found this instruction helpful
Took the screw out of the glass door holder, bent the clips up and removed the broken glass. While this was open chenged the light bulbs as well. Put new glass in bent the holding clips down and closed the doors and installed the screws again. So nice to have good light again and also new glass in them. Never noticed they were broken before.

BY THE WAY PARTS SELECT IS VERY PROMPT AND I RECEIVED MY PARTS IN ONE DAY AFTER THEY SHIPPED. SHIPPED ON MONDAY GOT THEM TUESDAY, thanks parts select for your promtness and speedy work for shipment.

Two counter light bulbs burned out

  • Customer: Jerry from Rio Vista, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 16 people found this instruction helpful
After removing the screws holding the 2 cover plates in position, I removed the halogen light bulbs with my fingers. Then I placed a paper towel around the first replacement bulb and lined up the two wire connectors with the two holes in the receptacle. I pushed in, but the bulb's probes did not slide into the receptacle. I spent five minutes aligning and pushing but to no avail. Then I removed the filter screen on the side of the receptacle, shined a flashlight beam on the receptacle, and with an improved view of the two holes in the receptacle, slid the bulb in. The second bulb was inserted in a few minutes, and the job was done. Whoever designed the halogen bulb was not as bright as Thomas Edison.
All Instructions for the JVM2070SK02
16-30 of 160